Gigabyte GA-VM800PMC First / Second / Third Boot Device, Password Check, CPU Hyper-Threading Note

Page 33

First / Second / Third Boot Device

Floppy

Select your boot device priority by Floppy.

LS120

Select your boot device priority by LS120.

Hard Disk

Select your boot device priority by Hard Disk.

CDROM

Select your boot device priority by CDROM.

ZIP

Select your boot device priority by ZIP.

USB-FDD

Select your boot device priority by USB-FDD.

USB-ZIP

Select your boot device priority by USB-ZIP.

USB-CDROM

Select your boot device priority by USB-CDROM.

USB-HDD

Select your boot device priority by USB-HDD.

Legacy LAN

Select your boot device priority by Legacy LAN.

Disabled

Disable this function.

Password Check

System

The system can not boot and can not access to Setup page will be denied if the

 

correct password is not entered at the prompt.

Setup

The system will boot, but access to Setup will be denied if the correct password

 

is not entered at the prompt. (Default value)

CPU Hyper-Threading (Note)

Enabled

Enable CPU Hyper Threading Feature. Please note that this feature is only

 

working for operating system with multi processors mode supported.

 

(Default value)

Disabled

Disable CPU Hyper Threading.

Limit CPUID Max. to 3 (Note)

Enabled

Limit CPUID Maximum value to 3 when use older OS like NT4.

Disabled

Disable CPUID Limit for windows XP. (Default value)

No-Execute Memory Protect(Note)

Enabled

Enable No-Execute Memory Protect function. (Default value)

Disabled

Disable No-Execute Memory Protect function.

CPU Enhanced Halt (C1E) (Note)

Enabled

Enable CPU Enhanced Halt (C1E) function. (Default value)

Disabled

Disable CPU Enhanced Halt (C1E) function.

CPU Thermal Monitor 2 (TM2) (Note)

Enabled

Enable CPU Thermal Monitor 2 (TM2) function. (Default value)

Disabled

Disable CPU Thermal Monitor 2 (TM2) function.

CPU EIST Function (Note)

Enabled

Enable CPU EIST function. (Default value)

Disabled

Disable EIST function.

Virtualization Technology (Note)

Enabled

Enable Virtualization Technology function. (Default value)

Disabled

Disable Virtualization Technology function.

(Note) This item will show up when you install a processor that supports this function.

English

- 33 -

BIOS Setup

Image 33
Contents GA-VM800PMC GA-VM800PMC Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-VM800PMC Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorSpdifio S/PDIF In/Out Connector Cdin CD in ConnectorFUSB1 / FUSB2 Front USB Connectors Surcen Surround Center ConnectorCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BatteryMain Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. D5„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0/1 Master, SlaveIDE Channel 2/3 Master Drive a Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Init Display FirstVGA Share Memory Size Password Check First / Second / Third Boot DeviceCPU Hyper-Threading Note Limit Cpuid Max. to 3 NoteSata Mode OnBoard LAN Boot ROMOnChip Serial ATA AC97 AudioEPP Mode Select Parallel Port ModeUSB 2.0 Controller USB Keyboard SupportPower Management Setup Resume by Alarm Mouse Power OnPME Event Wake Up Modem Ring ResumePnP/PCI Configurations System / CPU Temperature Current VoltageV Vcore / DDR Power / +3.3V / +12VSystem Warning Temperature Case OpenedCPU Warning Temperature SYS / CPU FAN Fail WarningCPU Smart FAN Control Note Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionBoot from CD/DVD F9 Xpress Recovery2 System requirementsMain Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Configuring Sata Hard Drives To configure Sata hard drives, follow the steps belowInstall Sata hard drives in your system RAID Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System