Gigabyte GA-VM800PMC Entering the Q-FlashTMutility, Task menu for Dual Bios utility, Action bar

Page 53

Entering the Q-FlashTMutility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Exploring the Q-FlashTM / Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

English

Task menu for Dual BIOS utility

Task menu for Q-FlashTMutility

									Dual BIOS utility bar
			Dual BIOS Utility
			Dual BIOS Utility

		Boot From		Main Bios
		Main ROM Type/Size		SST 49LF003A		512K
		Backup ROM Type/Size		SST 49LF003A		512K
		Wide Range Protection		Disable
			Boot From	Main Bios
			Auto Recovery	Enable
			Halt On Error	Disable
			Copy Main ROM Data to Backup
			Load Default Settings
			Save Settings to CMOS						Q-FlashTMutility title
			Save Settings to CMOS
			Q-Flash Utility
			Q-Flash Utility
			Load Main BIOS from Floppy						bar
			Load Backup BIOS from Floppy						bar
			Save Main BIOS to Floppy
			Save Backup BIOS to Floppy						Action bar
			Save Backup BIOS to Floppy
		Enter : Run	:Move	ESC:Reset	F10:Power Off
		Enter : Run	:Move	ESC:Reset	F10:Power Off

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu- tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons mentioned on your keyboards to perform these actions.

- 53 -

Appendix

Image 53

Contents GA-VM800PMC GA-VM800PMC Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-VM800PMC Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorSpdifio S/PDIF In/Out Connector Cdin CD in ConnectorFUSB1 / FUSB2 Front USB Connectors Surcen Surround Center ConnectorCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BatteryMain Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. D5„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 2/3 Master TimeIDE Channel 0/1 Master, Slave Drive a Floppy 3 Mode Support for Japan AreaHalt on MemoryVGA Share Memory Size Hard Disk Boot PriorityInit Display First Password Check First / Second / Third Boot DeviceCPU Hyper-Threading Note Limit Cpuid Max. to 3 NoteSata Mode OnBoard LAN Boot ROMOnChip Serial ATA AC97 AudioEPP Mode Select Parallel Port ModeUSB 2.0 Controller USB Keyboard SupportPower Management Setup Resume by Alarm Mouse Power OnPME Event Wake Up Modem Ring ResumePnP/PCI Configurations System / CPU Temperature Current VoltageV Vcore / DDR Power / +3.3V / +12VSystem Warning Temperature Case OpenedCPU Smart FAN Control Note CPU Warning TemperatureSYS / CPU FAN Fail Warning Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery2 Xpress Recovery2 IntroductionBoot from CD/DVD F9 Xpress Recovery2 System requirementsLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below RAID Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System