Gigabyte GA-7VT600 manual DDR Introduction

Page 20

English

1.The DIMM slot has a notch, so the DIMM memory module can only fit in one direction.

2.Insert the DIMM memory module vertically into the DIMM slot. Then push it down.

3.Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.

Reverse the installation steps when you wish to remove the DIMM module.

DDR Introduction

Established on the existing SDRAM infrastructure, DDR (Double Data Rate) memory is a high performance and cost-effective solution that allows easy adoption for memory vendors, OEMs, and system integrators.

DDR memory is a great evolutionary solution for the PC industry that builds on the existing SDRAM architecture, yet make the awesome advances in solving the system performance bottleneck by doubling the memory bandwidth. Nowadays, with the highest bandwidth of 3.2GB/s of DDR400 memory and complete line of DDR400/333/266/200 memory solutions, DDR memory is the best choice for building high performance and low latency DRAM subsystem that are suitable for servers, workstations, and full range of desktop PCs.

GA-7VT600(-L) Motherboard

- 16 -

Image 20
Contents AGP 4X/8X notch Page Declaration of Conformity Product Name Motherboard Model NumberGA-7VT600 Supplementary InformationGA-7VT600-L AMD Socket a Processor Motherboard Table of Contents Table of Content Item Checklist Installing the motherboard to the chassis…Features Summary Chapter IntroductionVIA VT6103L GA-7VT600-L Motherboard Layout GA-7VT600Block Diagram English English Hardware Installation Process StepSet System Jumper JP1 JP1 CPU ClockInstall the Central Processing Unit CPU Socket Actuation LeverCPU Cooling Fan Installation Install Memory Modules DDRDDR Introduction Install Expansion Cards Parallel Port and Serial Ports Coma / Comb Connect Ribbon Cables, Cabinet Wires and Power SupplyPS/2 Keyboard and PS/2 Mouse Connector USB/LAN* Connector Audio ConnectorsATX ATX Power CI Case OpenCpufan CPU FAN Connector Sysfan System FAN ConnectorATX ATX Power Connector IDE1/ IDE2IDE1/IDE2 ConnectorFDD Floppy Connector Fpanel 2 x 10 pins Connector Battery Battery Faudio Front Audio ConnectorSurcen Surround Center Connector Cdin CD In ConnectorAuxin AUX In Connector Spdifio Spdif In/Out ConnectorUSB1 / FUSB2 Front USB Connector, Yellow Game Game ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish Bios Setup Main Menu For example Bios Ver. F4c Status Page Setup Menu / Option Page Setup MenuStandard Cmos Features Advanced Bios FeaturesPowerManagement Setup PnP/PCI ConfigurationsLoad Fail-Safe Defaults Load Optimized DefaultsTime Standard Cmos FeaturesDate Drive a / Drive B Floppy 3 Mode Support for Japan AreaIDE Primary Master, Slave / Secondary Master, Slave Halt on MemoryBase Memory Extended MemoryAdvanced Bios Features First / Second / Third Boot devicePassword Check Integrated Peripherals SPPOnChipIDEChannel0 OnChipIDEChannel1AC97Audio VIA Onboard LANVIA LAN Boot ROM USB Mouse SupportOnboard Serial Port OnBoard Parallel portUart Mode Select Parallel Port ModeGame PortAddress Midi PortAddressPower Management Setup Acpi SuspendTypePower LED in S1 state KeyboardPowerOnMouse Power On Soft-off by PwrbtnResume byAlarm PMEEventWakeupPnP/PCI Configurations PCI1/PCI5 IRQAssignmentPCI2 IRQAssignment PCI3 IRQAssignmentReset Case Open Status Case Opened PC Health StatusCurrent System Temperature C Current CPU Temperature CCurrent CPU FAN / System FAN Speed RPM Fan Fail Warning CPU / SystemCPU Host Frequency MHz By switch SW1 Frequency/Voltage ControlSpread Spectrum Modulated CPU Host Clock ControlPCI/AGPFrequencyMHz DRAMClockMHzCPU OverVoltage Control AGPOverVoltage ControlLoad Fail-Safe Defaults Load Fail-Safe Defaults Y/N? NLoad Optimized Defaults Load Optimized Defaults Y/N? NSet Supervisor/User Password Enter PasswordSave & Exit Setup Save to Cmos and Exit Y/N? YExit Without Saving Quit Without Saving Y/N? NEnglish @BIOS Introduction Technical ReferenceEasyTune 4 Introduction Flash Bios Method Introduction Method 1 Q-Flash Flash Bios Method IntroductionEntering the Q-Flashutility Exploring the Q-Flash/Dual Bios utility screen Task menu for Dual Bios utility Task menu for Q-FlashutilityAction bar StepsBios file in the floppy disk You can press Enter to continue Please press any key to continue Bios file becomes F12 after updating Press Y on your keyboard to load defaults Entering the Q-Flashutility Exploring the Q-Flashutility screen Flash Type/Size Congratulation!! You have updated Bios successfully Method 2 @BIOS Utility English Stereo Speakers Connection and Settings 6-Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing Introduction Manual setting Xpress Recovery Introduction What is Xpress Recovery?How to use the Xpress Recovery F9 For Xpress RecoveryText Mode Exit and Restart Install Drivers Picture below are shown in Windows XPItem Description Software Application Software Information EasyTune 4 Utilities Installation FAQ Award Bios Beep Codes English Troubleshooting END Technical Support/RMA Sheet Appendix E Acronyms LBA English English GA-7VT600-L Motherboard 100