Gigabyte GA-7VT600 manual PMEEventWakeup, Resume byAlarm

Page 49

)PMEEventWakeup

When set at Enabled, any PCI-PM event awakes the system from a PCI-PM controlled state. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.

Disabled

Disabled PME Event Wake up function.

Enabled

Enabled PME Event Wake up function. (Default Value)

)ModemRingOn/WakeOnLAN (When AC Back Function set to [Soft-Off])

You can enable wake on LAN feature by the "ModemRingOn/WakeOnLAN" or "PME Event Wake up" when the M/B has "WOL" onboard connector. Only enabled the feature by "PME Event Wake up". An incoming call via modem awakes the system from its soft-off mode. When set at Enabled, an input signal comes from the other client.

Server on the LAN awaks the system from a soft off state if connected over LAN.

Disabled

Disabled Modem Ring On / Wake On LAN function.

Enabled

Enabled Modem Ring On / Wake On LAN function. (Default Value)

)Resume byAlarm

You can set "Resume by Alarm" item to enabled and key in Data/time to power on system.

Disabled

Disable this function. (Default Value)

Enabled

Enable alarm function to POWER ON system.

If RTC Alarm Lead To Power On is Enabled.

Date (of Month) Alarm :

Everyday, 1~31

Time (hh: mm: ss) Alarm :

(0~23) : (0~59) : (0~59)

English

- 45 -

BIOS Setup

Image 49
Contents AGP 4X/8X notch Page Declaration of Conformity Supplementary Information Product Name Motherboard Model NumberGA-7VT600GA-7VT600-L AMD Socket a Processor Motherboard Table of Contents Table of Content Installing the motherboard to the chassis… Item ChecklistChapter Introduction Features SummaryVIA VT6103L GA-7VT600 GA-7VT600-L Motherboard LayoutBlock Diagram English English Step Hardware Installation ProcessJP1 CPU Clock Set System Jumper JP1Socket Actuation Lever Install the Central Processing Unit CPUCPU Cooling Fan Installation DDR Install Memory ModulesDDR Introduction Install Expansion Cards PS/2 Keyboard and PS/2 Mouse Connector Connect Ribbon Cables, Cabinet Wires and Power SupplyParallel Port and Serial Ports Coma / Comb Audio Connectors USB/LAN* ConnectorCI Case Open ATX ATX PowerSysfan System FAN Connector Cpufan CPU FAN ConnectorIDE1/ IDE2IDE1/IDE2 Connector ATX ATX Power ConnectorFDD Floppy Connector Fpanel 2 x 10 pins Connector Faudio Front Audio Connector Battery BatteryCdin CD In Connector Surcen Surround Center ConnectorSpdifio Spdif In/Out Connector Auxin AUX In ConnectorGame Game Connector USB1 / FUSB2 Front USB Connector, YellowClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish Bios Setup Status Page Setup Menu / Option Page Setup Menu Main Menu For example Bios Ver. F4cStandard Cmos Features Advanced Bios FeaturesPnP/PCI Configurations PowerManagement SetupLoad Fail-Safe Defaults Load Optimized DefaultsDate Standard Cmos FeaturesTime IDE Primary Master, Slave / Secondary Master, Slave Floppy 3 Mode Support for Japan AreaDrive a / Drive B Memory Halt onBase Memory Extended MemoryFirst / Second / Third Boot device Advanced Bios FeaturesPassword Check SPP Integrated PeripheralsOnChipIDEChannel1 OnChipIDEChannel0AC97Audio VIA Onboard LANUSB Mouse Support VIA LAN Boot ROMOnboard Serial Port OnBoard Parallel portParallel Port Mode Uart Mode SelectGame PortAddress Midi PortAddressAcpi SuspendType Power Management SetupKeyboardPowerOn Power LED in S1 stateMouse Power On Soft-off by PwrbtnPMEEventWakeup Resume byAlarmPCI1/PCI5 IRQAssignment PnP/PCI ConfigurationsPCI2 IRQAssignment PCI3 IRQAssignmentPC Health Status Reset Case Open Status Case OpenedCurrent CPU Temperature C Current System Temperature CCurrent CPU FAN / System FAN Speed RPM Fan Fail Warning CPU / SystemFrequency/Voltage Control CPU Host Frequency MHz By switch SW1Spread Spectrum Modulated CPU Host Clock ControlDRAMClockMHz PCI/AGPFrequencyMHzCPU OverVoltage Control AGPOverVoltage ControlLoad Fail-Safe Defaults Y/N? N Load Fail-Safe DefaultsLoad Optimized Defaults Y/N? N Load Optimized DefaultsEnter Password Set Supervisor/User PasswordSave to Cmos and Exit Y/N? Y Save & Exit SetupQuit Without Saving Y/N? N Exit Without SavingEnglish Technical Reference @BIOS IntroductionEasyTune 4 Introduction Method 1 Q-Flash Flash Bios Method Introduction Flash Bios Method IntroductionEntering the Q-Flashutility Exploring the Q-Flash/Dual Bios utility screen Task menu for Q-Flashutility Task menu for Dual Bios utilityAction bar StepsBios file in the floppy disk You can press Enter to continue Please press any key to continue Bios file becomes F12 after updating Press Y on your keyboard to load defaults Entering the Q-Flashutility Exploring the Q-Flashutility screen Flash Type/Size Congratulation!! You have updated Bios successfully Method 2 @BIOS Utility English 6-Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introduction Introduction of audio connectorsAuto-detecting Manual setting What is Xpress Recovery? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress RecoveryText Mode Exit and Restart Picture below are shown in Windows XP Install DriversItem Description Software Application Software Information EasyTune 4 Utilities Installation FAQ Award Bios Beep Codes English Troubleshooting END Technical Support/RMA Sheet Appendix E Acronyms LBA English English GA-7VT600-L Motherboard 100