Gigabyte GA-7VT600 Frequency/Voltage Control, Spread Spectrum Modulated, CPU Host Clock Control

Page 53

Frequency/Voltage Control

CMOS Setup Utility-Copyright (C) 1984-2003 Award Software

Frequency/Voltage Control

Spread Spectrum Modulated

[Enabled]

Item Help

CPU Host Clock Control

[Disable]

Menu Level

ÚCPU Host Frequency(MHz)

133

 

ÚPCI/AGP Frequency(MHz)

33/66

 

DRAM Clock(MHz)

[Auto]

 

CPU OverVoltage Control

[Auto]

 

AGP OverVoltage Control

[Auto]

 

DIMM OverVoltage Control

[Auto]

 

 

 

 

: Move

Enter:Select

+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values

F6:Fail-Safe Defaults

F7:Optimized Defaults

 

 

 

Figure 8: Frequency/Voltage Control

ÚThose items will be available when "CPU Host Clock Control" is set to Enabled.

)Spread Spectrum Modulated

Disabled

Disable clock spread spectrum.

Enabled

Enable clock spread spectrum.(Default value)

)CPU Host Clock Control

Note: If system hangs up before enter CMOS setup utility, wait for 20 sec for times out reboot . When time out occur, system will reset and run at CPU default Host clock at next boot.

Disable

Disable CPU Host Clock Control.(Default value)

Enable

Enable CPU Host Clock Control.

)CPU Host Frequency (MHz) (By switch SW1)

100

Set CPU Host Clock to 100MHz~132MHz.

133

Set CPU Host Clock to 133MHz~165MHz.

166

Set CPU Host Clock to 166MHz~200MHz.

200

Set CPU Host Clock to 200MHz~254MHz.

English

- 49 -

BIOS Setup

Image 53
Contents AGP 4X/8X notch Page Declaration of Conformity Supplementary Information Product Name Motherboard Model NumberGA-7VT600GA-7VT600-L AMD Socket a Processor Motherboard Table of Contents Table of Content Installing the motherboard to the chassis… Item ChecklistChapter Introduction Features SummaryVIA VT6103L GA-7VT600 GA-7VT600-L Motherboard LayoutBlock Diagram English English Step Hardware Installation ProcessJP1 CPU Clock Set System Jumper JP1Socket Actuation Lever Install the Central Processing Unit CPUCPU Cooling Fan Installation DDR Install Memory ModulesDDR Introduction Install Expansion Cards Parallel Port and Serial Ports Coma / Comb Connect Ribbon Cables, Cabinet Wires and Power SupplyPS/2 Keyboard and PS/2 Mouse Connector Audio Connectors USB/LAN* ConnectorCI Case Open ATX ATX PowerSysfan System FAN Connector Cpufan CPU FAN ConnectorIDE1/ IDE2IDE1/IDE2 Connector ATX ATX Power ConnectorFDD Floppy Connector Fpanel 2 x 10 pins Connector Faudio Front Audio Connector Battery BatteryCdin CD In Connector Surcen Surround Center ConnectorSpdifio Spdif In/Out Connector Auxin AUX In ConnectorGame Game Connector USB1 / FUSB2 Front USB Connector, YellowClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish Bios Setup Status Page Setup Menu / Option Page Setup Menu Main Menu For example Bios Ver. F4cStandard Cmos Features Advanced Bios FeaturesPnP/PCI Configurations PowerManagement SetupLoad Fail-Safe Defaults Load Optimized DefaultsTime Standard Cmos FeaturesDate Drive a / Drive B Floppy 3 Mode Support for Japan AreaIDE Primary Master, Slave / Secondary Master, Slave Memory Halt onBase Memory Extended MemoryFirst / Second / Third Boot device Advanced Bios FeaturesPassword Check SPP Integrated PeripheralsOnChipIDEChannel1 OnChipIDEChannel0AC97Audio VIA Onboard LANUSB Mouse Support VIA LAN Boot ROMOnboard Serial Port OnBoard Parallel portParallel Port Mode Uart Mode SelectGame PortAddress Midi PortAddressAcpi SuspendType Power Management SetupKeyboardPowerOn Power LED in S1 stateMouse Power On Soft-off by PwrbtnPMEEventWakeup Resume byAlarmPCI1/PCI5 IRQAssignment PnP/PCI ConfigurationsPCI2 IRQAssignment PCI3 IRQAssignmentPC Health Status Reset Case Open Status Case OpenedCurrent CPU Temperature C Current System Temperature CCurrent CPU FAN / System FAN Speed RPM Fan Fail Warning CPU / SystemFrequency/Voltage Control CPU Host Frequency MHz By switch SW1Spread Spectrum Modulated CPU Host Clock ControlDRAMClockMHz PCI/AGPFrequencyMHzCPU OverVoltage Control AGPOverVoltage ControlLoad Fail-Safe Defaults Y/N? N Load Fail-Safe DefaultsLoad Optimized Defaults Y/N? N Load Optimized DefaultsEnter Password Set Supervisor/User PasswordSave to Cmos and Exit Y/N? Y Save & Exit SetupQuit Without Saving Y/N? N Exit Without SavingEnglish Technical Reference @BIOS IntroductionEasyTune 4 Introduction Method 1 Q-Flash Flash Bios Method Introduction Flash Bios Method IntroductionEntering the Q-Flashutility Exploring the Q-Flash/Dual Bios utility screen Task menu for Q-Flashutility Task menu for Dual Bios utilityAction bar StepsBios file in the floppy disk You can press Enter to continue Please press any key to continue Bios file becomes F12 after updating Press Y on your keyboard to load defaults Entering the Q-Flashutility Exploring the Q-Flashutility screen Flash Type/Size Congratulation!! You have updated Bios successfully Method 2 @BIOS Utility English 6-Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing Introduction Manual setting What is Xpress Recovery? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress RecoveryText Mode Exit and Restart Picture below are shown in Windows XP Install DriversItem Description Software Application Software Information EasyTune 4 Utilities Installation FAQ Award Bios Beep Codes English Troubleshooting END Technical Support/RMA Sheet Appendix E Acronyms LBA English English GA-7VT600-L Motherboard 100