Gigabyte GA-K8VT800-RH user manual Feature Summary, Cpu

Page 10

English

1-2 Feature Summary

CPU

Š

Socket 754 for AMD AthlonTM 64 processor (K8)

 

Š

1600MT/s system bus

 

 

 

Chipset

Š

Northbridge: VIA K8T800

 

Š Southbridge: VIA VT8237R / VT8237R+

Memory

Š

3 DDR DIMM memory slots (supports up to 3GB)

 

Š Supports DDR 400/333/266/200 DIMMs

Slots

Š

1 AGP slot supports 8X/4X(1.5V) mode

 

Š

5 PCI slots

IDE Connections

Š

2 IDE connection (UDMA 133/100/66/33), allows connection

 

 

of 4 IDE devices

 

 

 

FDD Connections

Š

1 FDD connection, allows connection of 2 FDD devices

Onboard SATA

Š

2 Serial ATA ports from VIA VT8237R / VT8237R+ (SATA0, SATA1)(Note 1)

Peripherals

Š

1 parallel port supporting Normal/EPP/ECP mode

 

Š 2 serial ports (COMA, COMB)

 

Š 8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)

 

Š 1 front audio connector

 

Š

1 IR connector

 

Š 1 PS/2 keyboard port

 

Š 1 PS/2 mouse port

Onboard LAN

Š

Onboard RTL8100C chip (10/100 Mbit/s)

 

Š

1 RJ45 port

Onboard Audio

Š

ALC850 CODEC (UAJ)

 

Š Supports Jack Sensing function

 

Š Supports 2 / 4 / 6 / 8 channel audio(Note2)

 

Š Supports Line In ; Line Out ;MIC

 

Š Surround Back Speaker (by optional Audio Combo Kit)

 

Š

SPDIF In/Out connection

 

Š

CD In connection

I/O Control

Š

IT8705F

Hardware Monitor

Š

System voltage detection

 

Š

CPU temperature detection

Š CPU / System fan speed detection Š CPU / System fan failure warning

(Note 1) It is recommended to use SATA (1.5Gb/s) hard disks.

(Note 2) To set up an 8 channel audio configuration, you must use Audio Combo Kit (optional device).

GA-K8VT800-RH Motherboard

- 10 -

Image 10
Contents GA-K8VT800-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8VT800-RH Motherboard Layout K8VT800-GA -RHBlock Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of Memory Installation of the HeatsinkDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD Connector IDE1 / IDE2 IDE ConnectorSATA0/ SATA1 Serial ATA Connector PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center ConnectorUSB1 / FUSB2 Front USB Connector 15 IRBattery Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E8 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterMemory Drive A/Drive BHalt on Base MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckIntegrated Peripherals RAIDUSB 2.0 Controller OnBoard LAN Boot ROMUart Mode Select USB Keyboard SupportOnboard Parallel Port UR2 Duplex ModeParallel Port Mode Midi Port AddressPower Management Setup Acpi OSPME Event Wake Up Resume by AlarmModem Ring Resume PnP/PCI Configurations INTCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Top Performance Load Fail-Safe DefaultsDimm OverVoltage control Load Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the VIA VT8237R / VT8237R+ RAID Bios Entering the RAID Bios SetupCreate RAID Array Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete a RAID array Delete Array¡G Installing the RAID drivers Stereo Speakers Connection and Settings 4 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English Surround-Kit connector Spdif cable connector English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English Contact Us Taiwan HeadquartersGigabyte Global Service System