Gigabyte GA-K8VT800-RH Entering the Q-FlashTMutility, Task menu for Dual Bios utility, Action bar

Page 55

Entering the Q-FlashTMutility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Exploring the Q-FlashTM / Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

English

Task menu for Dual BIOS utility

Task menu for Q-FlashTMutility

									Dual BIOS utility bar
			Dual BIOS Utility
			Dual BIOS Utility

		Boot From		Main Bios
		Main ROM Type/Size		SST 49LF003A		512K
		Backup ROM Type/Size		SST 49LF003A		512K
		Wide Range Protection		Disable
			Boot From	Main Bios
			Auto Recovery	Enable
			Halt On Error	Disable
			Copy Main ROM Data to Backup
			Load Default Settings
			Save Settings to CMOS						Q-FlashTMutility title

			Q-Flash Utility
			Q-Flash Utility
			Load Main BIOS from Floppy						bar
			Load Backup BIOS from Floppy						bar
			Save Main BIOS to Floppy
			Save Backup BIOS to Floppy						Action bar
			Save Backup BIOS to Floppy
		Enter : Run	:Move	ESC:Reset	F10:Power Off
		Enter : Run	:Move	ESC:Reset	F10:Power Off

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu- tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons mentioned on your keyboards to perform these actions.

- 55 -

Appendix

Image 55

Contents GA-K8VT800-RH Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist K8VT800-GA -RH GA-K8VT800-RH Motherboard LayoutBlock Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of MemoryDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1 / IDE2 IDE Connector FDD FDD ConnectorPwrled SATA0/ SATA1 Serial ATA ConnectorFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out Connector15 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos BatteryEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E8 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 2/3 Master Standard Cmos FeaturesTime IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveBase Memory Drive A/Drive BHalt on MemoryPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceRAID Integrated PeripheralsUSB Keyboard Support OnBoard LAN Boot ROMUart Mode Select USB 2.0 ControllerMidi Port Address UR2 Duplex ModeParallel Port Mode Onboard Parallel PortAcpi OS Power Management SetupPME Event Wake Up Resume by AlarmModem Ring Resume INT PnP/PCI ConfigurationsCurrent CPU/SYSTEM FAN Speed RPM Current CPU TemperaturePC Health Status Current VoltageV Vcore / DDR25V / +3.3V / +12VFrequency/Voltage Control Top Performance Load Fail-Safe DefaultsDimm OverVoltage control Set Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities Xpress Recovery IntroductionWhat is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the VIA VT8237R / VT8237R+ RAID BiosCreate RAID Array Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete a RAID array Delete Array¡G Installing the RAID drivers 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Surround-Kit connector Spdif cable connector English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English Taiwan Headquarters Contact UsGigabyte Global Service System