Gigabyte GA-K8VT800-RH user manual Delete a RAID array Delete Array¡G

Page 67

B.Delete a RAID array (Delete Array)¡G

To delete a RAID array, select Delete Array and press <Enter>. After confirming the RAID array to be deleted, press <Enter> and the The selected array will be destoried. Are you sure? Continue? Press Y/N message will appear. Press <Y> to confirm or <N> to cancel.

VIA Tech. VT8237 SATA RAID BIOS Ver 2.31

Create Array

 

 

Delete a RAID array contain

 

Delete Array

 

 

the hard disks attached to

 

Create/Delete Spare

VIA RAID controller

 

 

Select Boot Array

 

F1

:

View Array/disk Status

 

Serial Number View

 

The selected array will be destoried.

,

: Move to next item

 

Enter

:

Confirm the selection

 

Are you sure? Continue? Press Y/N

ESC

:

Exit

 

 

Channel

Drive Name

Array Name

 

Mode

Size(GB)

Status

[*]Serial_Ch0 Master

ST3120026AS

ARRAY 0

 

SATA

111.79

Stripe0

[*]Serial_Ch1 Master

ST3120026AS

ARRAY 0

 

SATA

111.79

Stripe1

Figure 7

Except for RAID 1 array, all the data on the disk array will be destroyed after a disk array is deleted. When RAID 1 array is deleted, the data on the two RAID disks will be reserved and the two hard disks will become normal disk drives.

English

- 67 -

Appendix

Image 67
Contents GA-K8VT800-RH Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist K8VT800-GA -RH GA-K8VT800-RH Motherboard LayoutBlock Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of MemoryDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1 / IDE2 IDE Connector FDD FDD ConnectorPwrled SATA0/ SATA1 Serial ATA ConnectorFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out Connector15 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos BatteryEnglish English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E8 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 2/3 Master Standard Cmos FeaturesTime IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveBase Memory Drive A/Drive BHalt on MemoryPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceRAID Integrated PeripheralsUSB Keyboard Support OnBoard LAN Boot ROMUart Mode Select USB 2.0 ControllerMidi Port Address UR2 Duplex ModeParallel Port Mode Onboard Parallel PortAcpi OS Power Management SetupPME Event Wake Up Resume by AlarmModem Ring Resume INT PnP/PCI ConfigurationsCurrent CPU/SYSTEM FAN Speed RPM Current CPU TemperaturePC Health Status Current VoltageV Vcore / DDR25V / +3.3V / +12VFrequency/Voltage Control Top Performance Load Fail-Safe DefaultsDimm OverVoltage control Set Supervisor/User Password Load Optimized DefaultsExit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities Xpress Recovery IntroductionWhat is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the VIA VT8237R / VT8237R+ RAID BiosCreate RAID Array Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete a RAID array Delete Array¡G Installing the RAID drivers 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Surround-Kit connector Spdif cable connector English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English Taiwan Headquarters Contact UsGigabyte Global Service System