Gigabyte GA-K8VT800-RH user manual USB 2.0 Controller, USB Keyboard Support, USB Mouse Support

Page 36

English

USB 2.0 Controller

Disabled

Disable USB 2.0 controller.

Enabled

Enable USB 2.0 controller. (Default value)

USB Keyboard Support

Enabled

Enable USB keyboard support.

Disabled

Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled

Enable USB mouse support.

Disabled

Disable USB mouse support. (Default value)

Onboard H/W LAN

Enabled

Enable onboard LAN chip function. (Default value)

Disabled

Disable onboard LAN chip function.

OnBoard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled

Enable this function.

Disabled

Disable this function. (Default value)

Onboard FDC Controller

Enabled

Enable onboard FDC controller. (Default value)

Disabled

Disable onboard FDC controller.

Onboard Serial Port 1

Auto

BIOS will automatically setup the port 1 address.

3F8/IRQ4

Enable onboard Serial port 1 and address is 3F8. (Default value)

2F8/IRQ3

Enable onboard Serial port 1 and address is 2F8.

3E8/IRQ4

Enable onboard Serial port 1 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 1 and address is 2E8.

Disabled

Disable onboard Serial port 1.

Onboard Serial Port 2

Auto

BIOS will automatically setup the port 2 address.

3F8/IRQ4

Enable onboard Serial port 2 and address is 3F8.

2F8/IRQ3

Enable onboard Serial port 2 and address is 2F8. (Default value)

3E8/IRQ4

Enable onboard Serial port 2 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 2 and address is 2E8.

Disabled

Disable onboard Serial port 2.

UART Mode Select

This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.

Normal

Set onboard I/O chip UART to Normal mode.(Default value)

IrDA

Set onboard I/O chip UART to IrDA mode.

ASKIR

Set onboard I/O chip UART to ASKIR mode.

GA-K8VT800-RH Motherboard

- 36 -

Image 36
Contents GA-K8VT800-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8VT800-RH Motherboard Layout K8VT800-GA -RHBlock Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of Memory Installation of the HeatsinkDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD Connector IDE1 / IDE2 IDE ConnectorSATA0/ SATA1 Serial ATA Connector PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center ConnectorUSB1 / FUSB2 Front USB Connector 15 IRBattery Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E8 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3 MasterDrive A/Drive B Halt onMemory Base MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckIntegrated Peripherals RAIDOnBoard LAN Boot ROM Uart Mode SelectUSB 2.0 Controller USB Keyboard SupportUR2 Duplex Mode Parallel Port ModeOnboard Parallel Port Midi Port AddressPower Management Setup Acpi OSResume by Alarm PME Event Wake UpModem Ring Resume PnP/PCI Configurations INTCurrent CPU Temperature PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Load Fail-Safe Defaults Top PerformanceDimm OverVoltage control Load Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the VIA VT8237R / VT8237R+ RAID Bios Entering the RAID Bios SetupCreate RAID Array Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete a RAID array Delete Array¡G Installing the RAID drivers Stereo Speakers Connection and Settings 4 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English Surround-Kit connector Spdif cable connector English Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing and UAJ IntroductionAuto-detecting Manual setting Enable UAJ functionUAJ Introduction Troubleshooting English Contact Us Taiwan HeadquartersGigabyte Global Service System