Gigabyte GA-K8VT800-RH user manual Advanced Bios Features, Hard Disk Boot Priority, Password Check

Page 34

English

2-2

Advanced BIOS Features

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 

 

 

 

Advanced BIOS Features

 

 

`

Hard Disk Boot Priority

[Press Enter]

Item Help

 

First Boot Device

[Floppy]

 

Menu Level`

 

Second Boot Device

[Hard Disk]

 

 

 

Third Boot Device

[CDROM]

 

Select Hard Disk Boot

 

Password Check

[Setup]

 

Device Priority

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

 

 

 

 

 

 

 

 

Hard Disk Boot Priority

Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.

Use <> or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu.

First / Second / Third Boot Device

Floppy

Select your boot device priority by Floppy.

LS120

Select your boot device priority by LS120.

Hard Disk

Select your boot device priority by Hard Disk.

CDROM

Select your boot device priority by CDROM.

ZIP

Select your boot device priority by ZIP.

USB-FDD

Select your boot device priority by USB-FDD.

USB-ZIP

Select your boot device priority by USB-ZIP.

USB-CDROM

Select your boot device priority by USB-CDROM.

USB-HDD

Select your boot device priority by USB-HDD.

Legacy LAN

Select your boot device priority by LAN.

Disabled

Select your boot device priority by Disabled.

Password Check

System

The system can not boot and can not access to Setup page will be denied if the

 

correct password is not entered at the prompt.

Setup

The system will boot, but access to Setup will be denied if the correct password is

 

not entered at the prompt. (Default value)

GA-K8VT800-RH Motherboard

- 34 -

Image 34
Contents GA-K8VT800-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8VT800-RH Motherboard Layout K8VT800-GA -RHBlock Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of Memory Installation of the HeatsinkDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD Connector IDE1 / IDE2 IDE ConnectorSATA0/ SATA1 Serial ATA Connector PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center ConnectorUSB1 / FUSB2 Front USB Connector 15 IRBattery Clrcmos Clear CmosEnglish English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E8 „ Set User Password „ Load Optimized Defaults „ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterMemory Drive A/Drive BHalt on Base MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckIntegrated Peripherals RAIDUSB 2.0 Controller OnBoard LAN Boot ROMUart Mode Select USB Keyboard SupportOnboard Parallel Port UR2 Duplex ModeParallel Port Mode Midi Port AddressPower Management Setup Acpi OSPME Event Wake Up Resume by AlarmModem Ring Resume PnP/PCI Configurations INTCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Top Performance Load Fail-Safe DefaultsDimm OverVoltage control Load Optimized Defaults Set Supervisor/User PasswordSave & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the VIA VT8237R / VT8237R+ RAID Bios Entering the RAID Bios SetupCreate RAID Array Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete a RAID array Delete Array¡G Installing the RAID drivers Stereo Speakers Connection and Settings 4 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English Surround-Kit connector Spdif cable connector English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English Contact Us Taiwan HeadquartersGigabyte Global Service System