Gigabyte GA-8IP775 Series user manual Dual Channel DDR

Page 15

Dual Channel DDR

GA-8IP775 series supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will add double up to 6.4GB/s.

GA-8IP775 series includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel A : DDR 1, DDR 2

Channel B : DDR 3, DDR 4

If you want to operate the Dual Channel Technology, please note the following explanations due to the lim itation of Intel chipset specifications.

1.One/three DDR memory module is installed: The Dual Channel Technology can't operate when only one DDR memory module is installed.

2.Two DDR memory modules are installed (the same memory size and type): The Dual Channel Technology will operate when two memory modules are inserted individually into Channel A and B. If you install two memory modules in the same channel, the Dual Channel Technology will not operate.

3.Four DDR memory modules are installed: Ifyou install four memory modules at the same time, the Dual Channel Technology will operate only when those modules have the same memory size and type.

We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same color in order for Dual Channel Technology to work.

The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)

 

DDR 1

DDR 2

DDR 3

DDR 4

2 memorymodules

DS/SS

X

DS/SS

X

 

 

 

 

 

 

X

DS/SS

X

DS/SS

 

 

 

 

 

4 memorymodules

DS/SS

DS/SS

DS/SS

DS/SS

 

 

 

 

 

English

- 15 -

Hardware Installation

Image 15
Contents GA-8IP775 Series Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers P4 Titan GA-8IP775-GBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryBios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink DDR Installation of MemoryDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector IDE1/IDE2 IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1 Serial ATA Connector FDD Floppy ConnectorFpanel Front Panel Jumper PwrledSurcen Faudio Front Audio ConnectorSpdifio Spdif In/Out Cdin CDIrcir USB1 / FUSB2 Front USB ConnectorInfolink Game Game ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBATBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E2 „ Exit Without Saving „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0 Master, Slave/IDE Channel 1 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceLimit Cpuid Max. to CPU Hyper-ThreadingIntegrated Peripherals On-Chip Primary PCI IDEOn-Chip Secondary PCI IDE On-chip Sata Sata Port0 Configure asSata Port1 Configure as Onboard LAN Boot ROMECP Mode Use DMA Uart Mode SelectUR2 Duplex Mode Parallel Port ModeCIR Port Address Game Port AddressMidi Port Address Midi Port IRQModemRingOn/WakeOnLAN Power Management SetupKB Power on Password Resume by AlarmPower On By Mouse Power On By KeyboardPCI 1/PCI 5 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU FAN PIN Type CPU Smart FAN ControlCPU Host Frequency Mhz Frequency/Voltage ControlCPU Clock Ratio CPU Host Clock ControlDimm OverVoltage Control Memory Frequency ForMemory Frequency Mhz AGP/PCI/SRC Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities Xpress Recovery IntroductionWhat is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 3 2 / 4 / 6 / 8 Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Analog Audio Output Mode English Channel Audio Setup using Audio Combo Kit, Optional Device English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction English Troubleshooting English English English Taiwan Headquarters Contact UsChina Shanghai