Gigabyte GA-8IP775 Series user manual Channel Analog Audio Output Mode

Page 68

English

4 Channel Analog Audio Output Mode

STEP 1 :

Connect the front channels to "Line Out", the rear channels to "Line In".

Line Out Line In

STEP 2 :

Following installation of the audio driver, you find a icon a Sound Effect icon on the lower right hand taskbar. Click the icon to select the function.

STEP 3 :

Click "Speaker Configuration" and select the "UAJ Function". Then click on the left selection bar and select "4CH Speaker" to complete 4 channel audio configuration.

GA-8IP775 Series Motherboard

- 68 -

Image 68
Contents GA-8IP775 Series Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers GA-8IP775-G P4 TitanBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUBios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory DDRDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1/IDE2 IDE ConnectorFDD Floppy Connector SATA0/SATA1 Serial ATA ConnectorPwrled Fpanel Front Panel JumperFaudio Front Audio Connector SurcenCdin CD Spdifio Spdif In/OutUSB1 / FUSB2 Front USB Connector IrcirGame Game Connector InfolinkCI Chassis Intrusion, Case Open Clrcmos Clear CmosBATBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E2 „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without SavingIDE Channel 0 Master, Slave/IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toOn-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE Sata Port0 Configure as Sata Port1 Configure asOnboard LAN Boot ROM On-chip SataUart Mode Select UR2 Duplex ModeParallel Port Mode ECP Mode Use DMAGame Port Address Midi Port AddressMidi Port IRQ CIR Port AddressPower Management Setup ModemRingOn/WakeOnLANResume by Alarm Power On By MousePower On By Keyboard KB Power on PasswordPnP/PCI Configurations PCI 1/PCI 5 IRQ AssignmentPC Health Status CPU Smart FAN Control CPU FAN PIN TypeFrequency/Voltage Control CPU Clock RatioCPU Host Clock Control CPU Host Frequency MhzMemory Frequency For Memory Frequency MhzAGP/PCI/SRC Frequency Mhz Dimm OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2 / 4 / 6 / 8 Channel Audio Function IntroductionChannel Analog Audio Output Mode English Channel Audio Setup using Audio Combo Kit, Optional Device English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction English Troubleshooting English English English Contact Us Taiwan HeadquartersChina Shanghai