Gigabyte GA-8IP775 Series user manual FDD Floppy Connector, SATA0/SATA1 Serial ATA Connector

Page 21

6)FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

3 4

3 3

21

7)SATA0/SATA1 (Serial ATA Connector)

Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly.

			Pin No.	Definition
			1	GND

	7	1	2	TXP

			3	TXN
			3	TXN

			4	GND

			5	RXN

			6	RXP

			7	GND

English

- 21 -

Hardware Installation

Image 21

Contents GA-8IP775 Series Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers P4 Titan GA-8IP775-GBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryBios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink DDR Installation of MemoryDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector IDE1/IDE2 IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1 Serial ATA Connector FDD Floppy ConnectorFpanel Front Panel Jumper PwrledSurcen Faudio Front Audio ConnectorSpdifio Spdif In/Out Cdin CDIrcir USB1 / FUSB2 Front USB ConnectorInfolink Game Game ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBATBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E2 „ Set User Password „ Set Supervisor Password„ Save & Exit Setup „ Exit Without SavingStandard Cmos Features TimeIDE Channel 0 Master, Slave/IDE Channel 1 Master, Slave Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingIntegrated Peripherals On-Chip Primary PCI IDEOn-Chip Secondary PCI IDE Sata Port1 Configure as Sata Port0 Configure asOnboard LAN Boot ROM On-chip SataUR2 Duplex Mode Uart Mode SelectParallel Port Mode ECP Mode Use DMAMidi Port Address Game Port AddressMidi Port IRQ CIR Port AddressModemRingOn/WakeOnLAN Power Management SetupPower On By Mouse Resume by AlarmPower On By Keyboard KB Power on PasswordPCI 1/PCI 5 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU FAN PIN Type CPU Smart FAN ControlCPU Clock Ratio Frequency/Voltage ControlCPU Host Clock Control CPU Host Frequency MhzMemory Frequency Mhz Memory Frequency ForAGP/PCI/SRC Frequency Mhz Dimm OverVoltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 3 2 / 4 / 6 / 8 Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Analog Audio Output Mode English Channel Audio Setup using Audio Combo Kit, Optional Device English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction English Troubleshooting English English English Taiwan Headquarters Contact UsChina Shanghai