Gigabyte GA-8IP775 Series user manual Integrated Peripherals, On-Chip Primary PCI IDE

Page 36

English

2-3	Integrated Peripherals
		CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
			Integrated Peripherals
	On-Chip Primary PCI IDE		[Enabled]						Item Help
	On-Chip Secondary PCI IDE		[Enabled]					Menu Level`
	On-Chip SATA		[Auto]
x	SATA Port0 Configure as		SATA Port0					If a hard disk
	SATA Port1 Configure as		SATA Port1					controller card is
	USB Controller		[Enabled]					used, set at Disabled
	USB 2.0 Controller		[Enabled]
	USB Keyboard Support		[Disabled]					[Enabled]
	USB Mouse Support		[Disabled]					Enable on-chip IDE
	AC97 Audio		[Auto]					Port
	Onboard H/W LAN (*)		[Enabled]
	Onboard LAN Boot ROM (*)		[Disabled]					[Disabled]
	Onboard Serial Port 1		[3F8/IRQ4]					Disable on-chip IDE
	Onboard Serial Port 2		[2F8/IRQ3]					Port
	UART Mode Select		[Normal]
x	UR2 Duplex Mode		Half
	Onboard Parallel Port		[378/IRQ7]
	Parallel Port Mode		[SPP]
x	ECP Mode Use DMA		3
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit				F1: General Help
	F5: Previous Values		F6: Fail-Save Default	F7: Optimized Defaults
		CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
			Integrated Peripherals
	Game Port Address		[201]						Item Help
	Midi Port Address		[Disabled]					Menu Level`
	Midi Port IRQ		10
	CIR Port Address		[Disabled]
x	CIR Port IRQ		11

KLJI: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
F5: Previous Values		F6: Fail-Save Default	F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.

On-Chip Secondary PCI IDE

Enabled	Enable onboard 2nd channel IDE port. (Default value)
Disabled	Disable onboard 2nd channel IDE port.

(*) Only for GA-8IP775-G.

GA-8IP775 Series Motherboard

- 36 -

Image 36

Contents GA-8IP775 Series Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers GA-8IP775-G P4 TitanBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUBios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory DDRDual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1/IDE2 IDE ConnectorFDD Floppy Connector SATA0/SATA1 Serial ATA ConnectorPwrled Fpanel Front Panel JumperFaudio Front Audio Connector SurcenCdin CD Spdifio Spdif In/OutUSB1 / FUSB2 Front USB Connector IrcirGame Game Connector InfolinkCI Chassis Intrusion, Case Open Clrcmos Clear CmosBATBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E2 „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without SavingStandard Cmos Features TimeIDE Channel 0 Master, Slave/IDE Channel 1 Master, Slave Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toIntegrated Peripherals On-Chip Primary PCI IDEOn-Chip Secondary PCI IDE Sata Port0 Configure as Sata Port1 Configure asOnboard LAN Boot ROM On-chip SataUart Mode Select UR2 Duplex ModeParallel Port Mode ECP Mode Use DMAGame Port Address Midi Port AddressMidi Port IRQ CIR Port AddressPower Management Setup ModemRingOn/WakeOnLANResume by Alarm Power On By MousePower On By Keyboard KB Power on PasswordPnP/PCI Configurations PCI 1/PCI 5 IRQ AssignmentPC Health Status CPU Smart FAN Control CPU FAN PIN TypeFrequency/Voltage Control CPU Clock RatioCPU Host Clock Control CPU Host Frequency MhzMemory Frequency For Memory Frequency MhzAGP/PCI/SRC Frequency Mhz Dimm OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2 / 4 / 6 / 8 Channel Audio Function IntroductionChannel Analog Audio Output Mode English Channel Audio Setup using Audio Combo Kit, Optional Device English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction English Troubleshooting English English English Contact Us Taiwan HeadquartersChina Shanghai