ATTO Technology 2500C operation manual Installation instructions, Serial interface, LED indicators

Page 13

Serial interface

The RS-232 serial port provides support for remote monitoring and management through a command line interface. It is set at the factory at 115,200 bps.

Pin outs of the RJ11 connector, part number CBL- 0911-001 are

Pin Description

2TXD

3Ground

4RXD

5Ground

LED indicators

The LED indicators can be viewed from the front of the iPBridge 2500R/D.

Ethernet Link & Activity: Each Ethernet port has

its own set of LEDs to show link status and speed as well as busy status.

SCSI 0 Activity, SCSI 1 Activity: each SCSI bus

has its own LED to show activity on that bus (numbered 0 and 1).

Fault: should light yellow when power has been applied, then immediately go dark. Software activates the LED if there is a system error.

Exhibit 1.1-1 ATTO iPBridge 2500R/D connector side

Installation instructions

The ATTO iPBridge 2500R/D offers a variety of ways to connect into a SAN.

1Note the serial number of your iPBridge for later use:

_____________________________________

2Install the iPBridge 2500R/D in your desktop or rackmount environment.

a.Attach “L” brackets so that front side with the LEDs face front and the connector side is at the back.

b.Install the iPBridge horizontally within the rack so it does not reduce the air flow within the rack.

3Connect the AC power cord from the iPBridge to the proper AC source outlet.

a.Properly ground the iPBridge to the rack equipment. The earth ground connection must be maintained.

b.The power requirements plus the power draw of the other equipment in the rack must not overload the supply circuit and/or wiring of the rack.

4Connect SCSI devices to the iPBridge. and attach CAT 6 or CAT 5E cables to the GbE data port(s) on the iPBridge. (For details, refer to the Appendix, Cabling, on page iii).

5Configure the iPBridge using the instructions in Configuring the iPBridge on page 9.

4 Installation: ATTO iPBridge 2500R/D

Image 13

Contents Atto iPBridgeTM 2500C/R/D Page Page Contents Copying iPBridge configurations Additional configurationsTroubleshooting Atto ExpressNAV interfaceDiagnostic commands Maintenance commandsAlternative interface options Serial port configuration commands Scsi configuration commandsEthernet commands ISCSI commands Ndmp commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyPage IPBridge 2500 provide storage options IPBridge2500 featuresIntelligent Bridging Architecture, the engine Connectivity, infrastructure solutions Possible storage ConfigurationsAtto iPBridge 2500R/D LED indicators Installation instructionsExhibit 1.1-1 Atto iPBridge 2500R/D connector side Serial interfaceBack connector side Atto iPBridge 2500C Operating Temperature 0-70C externalHeight of tallest component .535 inches Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Microsoft iSCSI Initiator changes Configuring the iPBridgeClick Launch Browser Getting an IP addressHow Ndmp works Ndmp configuration provides backupProcedure Setting up NdmpAssign Ndmp names to devices Map devices automatically Mapping devices NdmpMap devices manually Click AutoMapConfiguration mapping Ndmp Mapping devices iSCSI Single Target modeNode names Automatically configure Multiple Target mode Multiple Target modeManually configure Multiple Target mode Click on the Multi Target Mode enabled button Click SubmitExhibit 2.4-1 Examples of single and multiple target modes Mapping single vs. multi target modeExhibit 2.4-2 Mapping with Atto ExpressNAV Change the current user name, password Additional configurationsCreate a read only password or user name Set the Real Time ClockSnmp protocol Configuring Scsi devicesAtto ExpressNAV interface Accessing ExpressNAVBrowser compatibility To optimize ExpressNAV in Internet ExplorerExhibit 3.0-1 An ExpressNAV ExpressNAV pages Restart FirmwareHelp Using FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary stepsUsing ZModem over the serial port Copying iPBridge configurationsZModem send clone.cln Send File/ZModem sendInside out method TroubleshootingCheck the host event log Check the iPBridge event and trace logsCheck host versions Check for problems on attached devicesComponent check Checking Scsi devicesChecking the serial port Checking the iPBridge internal configurationChecking iPBridge Ethernet ports Checking the LAN/WANChecking the iSCSI OS driver Checking the iSCSI Host Adapter or NICChecking the Operating System Checking the applicationsChecking iPBridge Scsi ports Performance issuesChecking Ethernet Host Adapter or NIC Checking the host system Use the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog boxAtto Exhibit 7.0-1 Start up messagesCLI provides ASCII-based interface Command conventions Symbol IndicatesCommand Defaults Example CLI commands summarySntp 38 CLI General use commands VerboseMode UsernameMaintenance commands SNTPServer SpeedWriteDefaultSpeedWrite TimeDiagnostic commands DumpTraceLog DumpEventLogEventLog EventLogFilterRouteDisplay PingSCSIPortList SCSITargetsSNMPTrapAddress TemperatureSNMPTraps TailEventLogScsi configuration commands VirtualDriveResponse Performance enhancement to newly-mapped Scsi devicesSerialPortBaudRate Serial port configuration commandsSerialPortEcho 50 CLI Ethernet commands 52 CLI NDMPAuthType Ndmp commandsNDMPMaxVersion NDMPPortNumber54 CLI ISCSI commands ISNSServer ISNSLoginControlMultiTargetMode AutoMap Mapping commandsRoute List to the map which satisfies a search for the given LUN Appendix a Atto iPBridge, FibreBridge family Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/DIPBridge products Fibre Bridge products Scsi cabling Appendix B CablingCable types ExamplesEthernet connections Term Definition Appendix C GlossaryVi Appendix FCC Standards Radio and Television Interference Appendix D Safety standards and compliancesEuropean Standards Appendix E Atto accessories Contact Atto Technology, Inc Appendix F Warranty, contact information