ATTO Technology 2500C operation manual Appendix D Safety standards and compliances

Page 74

Appendix D Safety standards and compliances

The equipment described in this manual generates and uses radio frequency energy. If this equipment is not used in strict accordance with the manufacturer's instruction, it can and may cause interference with radio and television reception. Refer to the Technical Specification sheet available at www.attotech.com for a full list of certifications.

WARNING

Risk of explosion if battery is removed and/or replaced by an incorrect type. Dispose of used batteries in accordance with your local environmental regulations.

No operator serviceable components inside the iPBridge 2500C/R/D.

Do not remove cover of iPBridge 2500R/D. Refer servicing to qualified personnel.

FCC Standards: Radio and Television Interference

WARNING

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide a reasonable protection against such interference when operating in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures

•Move the receiving antenna.

•Relocate the bridge with respect to the receiver, or move the bridge away from the receiver.

•Plug the computer into a different outlet so the computer and receiver are on different branch circuits.

•If necessary, consult an ATTO authorized dealer, ATTO Technical Support Staff, or an experienced radio/television technician for additional suggestions.

The booklet How to Identify and Resolve Radio/TV Interference Problems prepared by the Federal Communications Commission is a helpful guide. It is available from the US Government printing office, Washington, DC 20402, Stock No. 004-000-00345-4.

Canadian Standards

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

vii

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 73 Page 75
Image 74
Page 73 Page 75
Contents Atto iPBridgeTM 2500C/R/D Page Page Contents Troubleshooting Additional configurationsCopying iPBridge configurations Atto ExpressNAV interfaceAlternative interface options Maintenance commandsDiagnostic commands Ethernet commands Scsi configuration commandsSerial port configuration commands Mapping commands Ndmp commandsISCSI commands Appendix a Atto iPBridge, FibreBridge familyPage Intelligent Bridging Architecture, the engine IPBridge2500 featuresIPBridge 2500 provide storage options Possible storage Configurations Connectivity, infrastructure solutionsAtto iPBridge 2500R/D Exhibit 1.1-1 Atto iPBridge 2500R/D connector side Installation instructionsLED indicators Serial interfaceBack connector side Height of tallest component .535 inches Operating Temperature 0-70C externalAtto iPBridge 2500C Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Configuring the iPBridge Microsoft iSCSI Initiator changesGetting an IP address Click Launch BrowserNdmp configuration provides backup How Ndmp worksAssign Ndmp names to devices Setting up NdmpProcedure Map devices manually Mapping devices NdmpMap devices automatically Click AutoMapConfiguration mapping Ndmp Node names Single Target modeMapping devices iSCSI Manually configure Multiple Target mode Multiple Target modeAutomatically configure Multiple Target mode Click on the Multi Target Mode enabled button Click SubmitMapping single vs. multi target mode Exhibit 2.4-1 Examples of single and multiple target modesExhibit 2.4-2 Mapping with Atto ExpressNAV Create a read only password or user name Additional configurationsChange the current user name, password Set the Real Time ClockConfiguring Scsi devices Snmp protocolBrowser compatibility Accessing ExpressNAVAtto ExpressNAV interface To optimize ExpressNAV in Internet ExplorerExhibit 3.0-1 An ExpressNAV ExpressNAV pages Help FirmwareRestart Updating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsZModem send clone.cln Copying iPBridge configurationsUsing ZModem over the serial port Send File/ZModem sendCheck the host event log TroubleshootingInside out method Check the iPBridge event and trace logsComponent check Check for problems on attached devicesCheck host versions Checking Scsi devicesChecking iPBridge Ethernet ports Checking the iPBridge internal configurationChecking the serial port Checking the LAN/WANChecking the Operating System Checking the iSCSI Host Adapter or NICChecking the iSCSI OS driver Checking the applicationsChecking Ethernet Host Adapter or NIC Performance issuesChecking iPBridge Scsi ports Checking the host system Use Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 7.0-1 Start up messages AttoCommand conventions Symbol Indicates CLI provides ASCII-based interfaceCLI commands summary Command Defaults ExampleSntp 38 CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TimeDiagnostic commands EventLog DumpEventLogDumpTraceLog EventLogFilterSCSIPortList PingRouteDisplay SCSITargetsSNMPTraps TemperatureSNMPTrapAddress TailEventLogScsi configuration commands Performance enhancement to newly-mapped Scsi devices VirtualDriveResponseSerialPortEcho Serial port configuration commandsSerialPortBaudRate 50 CLI Ethernet commands 52 CLI NDMPMaxVersion Ndmp commandsNDMPAuthType NDMPPortNumber54 CLI ISCSI commands MultiTargetMode ISNSLoginControlISNSServer Route Mapping commandsAutoMap List to the map which satisfies a search for the given LUN IPBridge products Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/DAppendix a Atto iPBridge, FibreBridge family Fibre Bridge products Cable types Appendix B CablingScsi cabling ExamplesEthernet connections Appendix C Glossary Term DefinitionVi Appendix Appendix D Safety standards and compliances FCC Standards Radio and Television InterferenceEuropean Standards Appendix E Atto accessories Appendix F Warranty, contact information Contact Atto Technology, Inc
Top Page Image Contents