ATTO Technology 2500C Ndmp commands, ISCSI commands, Mapping commands, Appendix B Cabling Iii

Page 8

ReadOnlyPassword

RMON

Username

ReadOnlyUsername

7.1.8 NDMP commands

53

NDMPAuthType

NDMPMaxVersion

NDMPPortNumber

NDMPStatus

7.1.9 iSCSI commands

55

iSCSIAlias iSCSIChap iSCSIChapSecret iSCSIPortNumber iSCSITarget iSCSITargetNameDisplay iSNSLoginControl iSNSServer MultiTargetMode

7.1.10 Mapping commands

57

AutoMap iSCSITarget iSCSITargetNameDisplay MultiTargetMode Route

RouteDisplay SCSIInitID SCSITargets

Appendix A ATTO iPBridge, FibreBridge family	i
iPBridge products
Fibre Bridge products
Appendix B Cabling	iii
SCSI cabling
Cable types
Examples
Connecting SCSI devices to SCSI ports
Ethernet connections
Appendix C Glossary	v
Appendix D Safety standards and compliances	vii
Appendix E ATTO accessories	ix
Appendix F Warranty, contact information	x
Manufacturer limited warranty
Contact ATTO Technology, Inc.

Image 8

Contents Atto iPBridgeTM 2500C/R/D Page Page Contents Additional configurations Copying iPBridge configurationsTroubleshooting Atto ExpressNAV interfaceAlternative interface options Maintenance commandsDiagnostic commands Ethernet commands Scsi configuration commandsSerial port configuration commands Ndmp commands ISCSI commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyPage Intelligent Bridging Architecture, the engine IPBridge2500 featuresIPBridge 2500 provide storage options Possible storage Configurations Connectivity, infrastructure solutionsAtto iPBridge 2500R/D Installation instructions LED indicatorsExhibit 1.1-1 Atto iPBridge 2500R/D connector side Serial interfaceBack connector side Height of tallest component .535 inches Operating Temperature 0-70C externalAtto iPBridge 2500C Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Configuring the iPBridge Microsoft iSCSI Initiator changesGetting an IP address Click Launch BrowserNdmp configuration provides backup How Ndmp worksAssign Ndmp names to devices Setting up NdmpProcedure Mapping devices Ndmp Map devices automaticallyMap devices manually Click AutoMapConfiguration mapping Ndmp Node names Single Target modeMapping devices iSCSI Multiple Target mode Automatically configure Multiple Target modeManually configure Multiple Target mode Click on the Multi Target Mode enabled button Click SubmitMapping single vs. multi target mode Exhibit 2.4-1 Examples of single and multiple target modesExhibit 2.4-2 Mapping with Atto ExpressNAV Additional configurations Change the current user name, passwordCreate a read only password or user name Set the Real Time ClockConfiguring Scsi devices Snmp protocolAccessing ExpressNAV Atto ExpressNAV interfaceBrowser compatibility To optimize ExpressNAV in Internet ExplorerExhibit 3.0-1 An ExpressNAV ExpressNAV pages Help FirmwareRestart Using Atto ExpressNAV Using FTP over GbEUpdating firmware Preliminary stepsCopying iPBridge configurations Using ZModem over the serial portZModem send clone.cln Send File/ZModem sendTroubleshooting Inside out methodCheck the host event log Check the iPBridge event and trace logsCheck for problems on attached devices Check host versionsComponent check Checking Scsi devicesChecking the iPBridge internal configuration Checking the serial portChecking iPBridge Ethernet ports Checking the LAN/WANChecking the iSCSI Host Adapter or NIC Checking the iSCSI OS driverChecking the Operating System Checking the applicationsChecking Ethernet Host Adapter or NIC Performance issuesChecking iPBridge Scsi ports Checking the host system Alternative interface options Use the serial port or headerUse Telnet Type iPBridge in the New Connection dialog boxExhibit 7.0-1 Start up messages AttoCommand conventions Symbol Indicates CLI provides ASCII-based interfaceCLI commands summary Command Defaults ExampleSntp 38 CLI General use commands Username VerboseModeMaintenance commands SpeedWriteDefault SNTPServerSpeedWrite TimeDiagnostic commands DumpEventLog DumpTraceLogEventLog EventLogFilterPing RouteDisplaySCSIPortList SCSITargetsTemperature SNMPTrapAddressSNMPTraps TailEventLogScsi configuration commands Performance enhancement to newly-mapped Scsi devices VirtualDriveResponseSerialPortEcho Serial port configuration commandsSerialPortBaudRate 50 CLI Ethernet commands 52 CLI Ndmp commands NDMPAuthTypeNDMPMaxVersion NDMPPortNumber54 CLI ISCSI commands MultiTargetMode ISNSLoginControlISNSServer Route Mapping commandsAutoMap List to the map which satisfies a search for the given LUN IPBridge products Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/DAppendix a Atto iPBridge, FibreBridge family Fibre Bridge products Appendix B Cabling Scsi cablingCable types ExamplesEthernet connections Appendix C Glossary Term DefinitionVi Appendix Appendix D Safety standards and compliances FCC Standards Radio and Television InterferenceEuropean Standards Appendix E Atto accessories Appendix F Warranty, contact information Contact Atto Technology, Inc