ATTO Technology 2500C operation manual Maintenance commands

Page 50

7.1.3 Maintenance commands

The CLI commands outlined in this chapter may be used to get information or perform functions which are used in a variety of situations with the ATTO iPBridge.

Date

Sets the date for the iPBridge if SNTP has been disabled or is not available.

Set syntax: set Date [MM] / [DD] / [YYYY]

Requires a SaveConfiguration command

Get syntax: get Date

FirmwareRestart

Causes the iPBridge to reboot, then re-initialize its firmware.

Immediate command: FirmwareRestart

MaxOpTemp

Establishes/reports the maximum enclosure temperature alarm in degrees Celsius. If the temperature of the iPBridge rises above the maximum MaxOpTemp, thermal control event handling occurs.

Valid entries are between 55 and 70 degrees C

Default: 70

Set syntax: set MaxOpTemp [55-70]

Requires a SaveConfiguration command

Get syntax: get MaxOpTemp

MinOpTemp

Establishes/reports the minimum enclosure temperature alarm in degrees Celsius. If the temperature of the iPBridge falls below the minimum MinOpTemp, thermal control event handling occurs. Valid entries are between 0 and 15 degrees.

Default: 0

Set syntax: set MinOpTemp [0-15]

Requires a SaveConfiguration command

Get syntax: get MinOpTemp

OpTempWarn

Controls the number of degrees in Celsius before a thermal control event handling occurs. Warnings are made via system log entries. Valid entries are between 0 and 15 degrees.

Default: 5

Set syntax: set OpTempWarn [0-15]

Requires a SaveConfiguration command

Get syntax: get OpTempWarn

Password

Specifies a password for all sessions: NDMP, telnet, FTP and ExpressNAV web-based interface. A prompt asks for the current password, to enter the new password, and to confirm the new password. Passwords are case sensitive, 0-32 characters with no spaces. An empty password can be configured by entering the Password confirmation prompts with no parameters. The command RestoreConfiguration default sets the password to its default value.

Default: Password

Set syntax: set Password

Requires a SaveConfiguration command

Reserve

Reservation of the iPBridge is implicit: once the configuration image is changed by any user of services, the iPBridge becomes RESERVED. Executing a SaveConfiguration or RestoreConfiguration RELEASES the iPBridge so that other services users may access it. When iPBridge services interface is RESERVED, set commands from other users are unavailable.

At least one interface must always have access to the iPBridge.

Immediate command: Reserve

RestoreConfiguration

Restores configuration to either the default configuration or the configuration last saved into non-volatile memory. The saved option undoes any changes made since the last save.

Immediate command: RestoreConfiguration [Default Saved]

SCSIPortReset

Resets the specified SCSI bus.

Immediate command: SCSIPortReset [sb]

41

ATTO Technology Inc. iPBridge Installation and Operation Manual

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Atto iPBridgeTM 2500C/R/D Page Page Contents Troubleshooting Additional configurationsCopying iPBridge configurations Atto ExpressNAV interfaceAlternative interface options Maintenance commandsDiagnostic commands Ethernet commands Scsi configuration commandsSerial port configuration commands Mapping commands Ndmp commandsISCSI commands Appendix a Atto iPBridge, FibreBridge familyPage Intelligent Bridging Architecture, the engine IPBridge2500 featuresIPBridge 2500 provide storage options Possible storage Configurations Connectivity, infrastructure solutionsAtto iPBridge 2500R/D Exhibit 1.1-1 Atto iPBridge 2500R/D connector side Installation instructionsLED indicators Serial interfaceBack connector side Height of tallest component .535 inches Operating Temperature 0-70C externalAtto iPBridge 2500C Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Configuring the iPBridge Microsoft iSCSI Initiator changesGetting an IP address Click Launch BrowserNdmp configuration provides backup How Ndmp worksAssign Ndmp names to devices Setting up NdmpProcedure Map devices manually Mapping devices NdmpMap devices automatically Click AutoMapConfiguration mapping Ndmp Node names Single Target modeMapping devices iSCSI Manually configure Multiple Target mode Multiple Target modeAutomatically configure Multiple Target mode Click on the Multi Target Mode enabled button Click SubmitMapping single vs. multi target mode Exhibit 2.4-1 Examples of single and multiple target modesExhibit 2.4-2 Mapping with Atto ExpressNAV Create a read only password or user name Additional configurationsChange the current user name, password Set the Real Time ClockConfiguring Scsi devices Snmp protocolBrowser compatibility Accessing ExpressNAVAtto ExpressNAV interface To optimize ExpressNAV in Internet ExplorerExhibit 3.0-1 An ExpressNAV ExpressNAV pages Help FirmwareRestart Updating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary stepsZModem send clone.cln Copying iPBridge configurationsUsing ZModem over the serial port Send File/ZModem sendCheck the host event log TroubleshootingInside out method Check the iPBridge event and trace logsComponent check Check for problems on attached devicesCheck host versions Checking Scsi devicesChecking iPBridge Ethernet ports Checking the iPBridge internal configurationChecking the serial port Checking the LAN/WANChecking the Operating System Checking the iSCSI Host Adapter or NICChecking the iSCSI OS driver Checking the applicationsChecking Ethernet Host Adapter or NIC Performance issuesChecking iPBridge Scsi ports Checking the host system Use Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog boxExhibit 7.0-1 Start up messages AttoCommand conventions Symbol Indicates CLI provides ASCII-based interfaceCLI commands summary Command Defaults ExampleSntp 38 CLI General use commands Username VerboseModeMaintenance commands SpeedWrite SpeedWriteDefaultSNTPServer TimeDiagnostic commands EventLog DumpEventLogDumpTraceLog EventLogFilterSCSIPortList PingRouteDisplay SCSITargetsSNMPTraps TemperatureSNMPTrapAddress TailEventLogScsi configuration commands Performance enhancement to newly-mapped Scsi devices VirtualDriveResponseSerialPortEcho Serial port configuration commandsSerialPortBaudRate 50 CLI Ethernet commands 52 CLI NDMPMaxVersion Ndmp commandsNDMPAuthType NDMPPortNumber54 CLI ISCSI commands MultiTargetMode ISNSLoginControlISNSServer Route Mapping commandsAutoMap List to the map which satisfies a search for the given LUN IPBridge products Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/DAppendix a Atto iPBridge, FibreBridge family Fibre Bridge products Cable types Appendix B CablingScsi cabling ExamplesEthernet connections Appendix C Glossary Term DefinitionVi Appendix Appendix D Safety standards and compliances FCC Standards Radio and Television InterferenceEuropean Standards Appendix E Atto accessories Appendix F Warranty, contact information Contact Atto Technology, Inc
Top Page Image Contents