ATTO Technology 2500C operation manual Contents

Page 4

Contents

 

1 iPBridge 2500 provide storage options

1

iPBridge2500 features

 

Connectivity, infrastructure solutions

 

1.1 ATTO iPBridge 2500R/D

3

Dimensions

Environment

Power

SCSI interface

Ethernet interface

Serial interface

LED indicators

Installation instructions

1.2 ATTO iPBridge 2500C

6

Dimensions

Environment

Power

SCSI interface

Ethernet interface

Serial interface

Installation instructions

2 Configuring the iPBridge

9

Microsoft iSCSI Initiator changes

 

2.1 Getting an IP address

10

2.2 NDMP configuration provides backup

11

How NDMP works

 

Setting up NDMP

 

Procedure

 

Assign NDMP names to devices

 

2.3 Mapping devices: NDMP

13

Map devices automatically

 

Map devices manually

 

Assign NDMP names to devices

 

2.4 Mapping devices: iSCSI

15

Node names

 

Single Target mode

 

Map devices automatically

 

Map devices manually

 

Multiple Target mode

 

Automatically configure Multiple Target mode

 

Manually configure Multiple Target mode

 

Image 4
Contents Atto iPBridgeTM 2500C/R/D Page Page Contents Additional configurations Copying iPBridge configurationsTroubleshooting Atto ExpressNAV interfaceDiagnostic commands Maintenance commandsAlternative interface options Serial port configuration commands Scsi configuration commandsEthernet commands Ndmp commands ISCSI commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyPage IPBridge 2500 provide storage options IPBridge2500 featuresIntelligent Bridging Architecture, the engine Possible storage Configurations Connectivity, infrastructure solutionsAtto iPBridge 2500R/D Installation instructions LED indicatorsExhibit 1.1-1 Atto iPBridge 2500R/D connector side Serial interfaceBack connector side Atto iPBridge 2500C Operating Temperature 0-70C externalHeight of tallest component .535 inches Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Configuring the iPBridge Microsoft iSCSI Initiator changesGetting an IP address Click Launch BrowserNdmp configuration provides backup How Ndmp worksProcedure Setting up NdmpAssign Ndmp names to devices Mapping devices Ndmp Map devices automaticallyMap devices manually Click AutoMapConfiguration mapping Ndmp Mapping devices iSCSI Single Target modeNode names Multiple Target mode Automatically configure Multiple Target modeManually configure Multiple Target mode Click on the Multi Target Mode enabled button Click SubmitMapping single vs. multi target mode Exhibit 2.4-1 Examples of single and multiple target modesExhibit 2.4-2 Mapping with Atto ExpressNAV Additional configurations Change the current user name, passwordCreate a read only password or user name Set the Real Time ClockConfiguring Scsi devices Snmp protocolAccessing ExpressNAV Atto ExpressNAV interfaceBrowser compatibility To optimize ExpressNAV in Internet ExplorerExhibit 3.0-1 An ExpressNAV ExpressNAV pages Restart FirmwareHelp Using Atto ExpressNAV Using FTP over GbEUpdating firmware Preliminary stepsCopying iPBridge configurations Using ZModem over the serial portZModem send clone.cln Send File/ZModem sendTroubleshooting Inside out methodCheck the host event log Check the iPBridge event and trace logsCheck for problems on attached devices Check host versionsComponent check Checking Scsi devicesChecking the iPBridge internal configuration Checking the serial portChecking iPBridge Ethernet ports Checking the LAN/WANChecking the iSCSI Host Adapter or NIC Checking the iSCSI OS driverChecking the Operating System Checking the applicationsChecking iPBridge Scsi ports Performance issuesChecking Ethernet Host Adapter or NIC Checking the host system Alternative interface options Use the serial port or headerUse Telnet Type iPBridge in the New Connection dialog boxExhibit 7.0-1 Start up messages AttoCommand conventions Symbol Indicates CLI provides ASCII-based interfaceCLI commands summary Command Defaults ExampleSntp 38 CLI General use commands Username VerboseModeMaintenance commands SpeedWriteDefault SNTPServerSpeedWrite TimeDiagnostic commands DumpEventLog DumpTraceLogEventLog EventLogFilterPing RouteDisplaySCSIPortList SCSITargetsTemperature SNMPTrapAddressSNMPTraps TailEventLogScsi configuration commands Performance enhancement to newly-mapped Scsi devices VirtualDriveResponseSerialPortBaudRate Serial port configuration commandsSerialPortEcho 50 CLI Ethernet commands 52 CLI Ndmp commands NDMPAuthTypeNDMPMaxVersion NDMPPortNumber54 CLI ISCSI commands ISNSServer ISNSLoginControlMultiTargetMode AutoMap Mapping commandsRoute List to the map which satisfies a search for the given LUN Appendix a Atto iPBridge, FibreBridge family Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/DIPBridge products Fibre Bridge products Appendix B Cabling Scsi cablingCable types ExamplesEthernet connections Appendix C Glossary Term DefinitionVi Appendix Appendix D Safety standards and compliances FCC Standards Radio and Television InterferenceEuropean Standards Appendix E Atto accessories Appendix F Warranty, contact information Contact Atto Technology, Inc