Tripp Lite 220/230/240V Pure Sine Wave Input/Output owner manual Other UPS Features Rear Panel

Page 7

Basic Operation continued

Other UPS Features (Rear Panel)

230V

220V

240V

230V

240V

230V

220V

230V

AC Receptacles: Your UPS features IEC-320-C13 outlets. These output receptacles provide your connected equipment with AC line power during normal operation and battery power during blackouts and brownouts. The UPS protects equipment connected to these receptacles against damaging surges and line noise.

Communications Ports (USB or RS-232): These ports connect your UPS to any workstation or server. Use with Tripp Lite’s PowerAlert Software and included cables to enable your computer to automatically save open files and shut down equipment during a blackout. Also use PowerAlert Software to mon- itor a wide variety of AC line power and UPS operating conditions. Consult your PowerAlert Software manual or contact Tripp Lite Customer Support for more information. See “USB and RS-232 Serial Communications” in the “Optional Installation” section for installation instructions.

Telephone/Network Protection Jacks: These jacks protect your equipment against surges over a telephone/network data line. Connecting your equipment to these jacks is optional. Your UPS will work properly without this connection.

Not compatible with PoE (Power Over Ethernet) applications.

Voltage DIP Switches: These switches enable the UPS to be set to match actual input voltage. If the Voltage DIP Switches are set above or below input voltage, the UPS will treat the input as a continuous overvoltage or undervolt- age condition, and will automatically adjust input voltage to match the Voltage DIP Switch setting. This will cause constant, unnecessary wear on the UPS.

Note: The Voltage DIP Switches must be set with the UPS turned OFF and disconnected from utility power. If the switches are set while the UPS is connected to utility power, the setting will not take effect.

Accessory Slot: Remove the small cover panel from this slot to install option- al accessories to remotely monitor and control your UPS. Refer to your acces- sory’s manual for installation instructions. Contact Tripp Lite Customer Support at (773) 869-1234 for more information, including a list of available SNMP, network management and connectivity products.

Input Breaker (SMX1500SLT): Protect your electrical circuit from overcur- rent draw from the UPS load. If this breaker trips, remove some of the load, then reset by pressing the breaker in.

Fan: The fan cools the UPS's internal components. It operates only when the UPS is in battery backup mode, is charging its batteries or is carrying a heavy electrical load.

7

Image 7
Contents SmartPro SLT UPS Location Warnings Important Safety InstructionsTurn the UPS on USB and RS-232 Serial Communications Buttons Front Panel Indicator Lights Front Panel Other UPS Features Rear Panel Carefully pull the front panel away from the UPS Manual del propietario Advertencias sobre la conexión de equipos Instrucciones de seguridad importantesAdvertencias sobre la ubicación del UPS Advertencias sobre la conexión del UPSEncienda el UPS Teléfono/gatos de conexión de red Comunicaciones USB y serie RS-232 Todos los modelosBotón ON/OFF/STANDBY Encendido/Apagado/Reserva Botones Panel frontalLuces indicadoras Panel frontal Operación básica continúaOtras funciones del UPS Panel posterior Almacenamiento Quite las baterías viejasConecte las nuevas baterías Reassemble UPSManuel du propriétaire Mises en garde Connexion déquipement Mises en garde Emplacement de lUPSDirectives de sécurité importantes Mises en garde Connexions de lUPSSMX750SLT Téléphoner/Crics de Protection De Réseau Boutons Panneau avant Voyants indicateurs Panneau avant Fonctionnement de base, suiteAutres caractéristiques de lUPS panneau arrière Réassemblez lUPS ServiceEnlever les anciennes piles Connecter de nouvelles pilesBesitzerhandbuch Bewahren SIE Diese Instruktionen AUS Wichtige SicherheitsinstruktionenSchalten Sie die USV ein Schließen Sie Ihr Gerät an die USV anUSB und RS-232 serielle Kommunikationsanschlüsse Taste „ON/OFF/STANDBY EIN/AUS/STABNDBY Tasten Vorderes BedienfeldAnzeigeleuchten Vorderes Bedienfeld Grundbetrieb FortsetzungSonstige USV-Funktionsmerkmale Rückseite Hinweis auf der Etikettierung Schließen Sie neue Batterien an220/230/240 Ñèíóñîèäàëüíûé âõîäíîé/âûõîäíîé ñèãíàë Ðóêîâîäñòâî ïîëüçîâàòåëÿÑîõðàíèòå ÝÒÈ Èíñòðóêöèè Âàæíûå èíñòðóêöèè ïî òåõíèêå áåçîïàñíîñòèÂêëþ÷èòå ÓÏÑ Áûñòðàÿ óñòàíîâêàÏîðòû ïîñëåäîâàòåëüíîé ñâÿçè 1USB è RS-232 âñå ìîäåëè Äîïîëíèòåëüíûé ìîíòàæÐîçåòêè äëÿ çàùèòû òåëåôîííîé ëèíèè Èëè ñåòè Êíîïêè Ïåðåäíÿÿ ïàíåëü Îñíîâíîé ðåæèì ðàáîòûÈíäèêàòîðíûå ëàìïî÷êè Ïåðåäíÿÿ ïàíåëü Îñíîâíîé ðåæèì ðàáîòû, ïðîäîëæåíèåÄðóãèå âîçìîæíîñòè ÓÏÑ Çàäíÿÿ ïàíåëü Îáñëóæèâàíèå Çàìåíà áàòàðåéÕðàíåíèå è îáñëóæèâàíèå Õðàíåíèå