Moxa Technologies VPort 2140 user manual Product Descriptions, Front Panel

Page 11

Introduction

Product Descriptions

Front Panel

1: RESET & DEFAULT buttons for restoring the system

There are two buttons located at the center of the front panel. One is labeled “RESET” and the other is labeled “DEFAULT.” “RESET” will force the system to restart at any point, meaning the system will perform the system diagnosis, and software installation may be necessary if the IP address is not fixed. “DEFAULT” will restore the default settings, and then force the system to restart.

When the system does not work properly, or VPort 2140’s IP address is not known, the administrator can use the restore function to restore VPort 2140’s factory default settings.

Step1: Click the “RESET” button once.

Step2: Press the “DEFAULT” button firmly until the “CONNECT” and “SERIAL” LEDs flash 2 times to run the system diagnosis and erase the system parameters.

2 & 3: BNC video outputs “OUT” & inputs “IN”

VPort 2140 allows up to 4 cameras to be attached at the same time. To ensure that the correct video modulation type is detected, cameras should be connected sequentially from “VIDEO 1” to “VIDEO 4” and powered on before the VPort is powered on. Video outputs also have four loop-through connectors for connecting with other capture devices, such as a time-lapsed VCR. To use the video outputs, the 75 Ohm DIP switch should be turned to the “OFF” position.

Although the analog cameras have 2 different standards, NTSC or PAL, all of the cameras connected to VPort 2140 Video Server should use the same standard.

4: Camera ID: “VIDEO 1,” “VIDEO 2,” “VIDEO 3,”and “VIDEO 4”

Each camera connected to VPort 2140 has a Camera ID used by VPort to identify the camera.

5: 75 Ohm DIP Switch

There are four 75 Ohm DIP switches numbered from “1” to “4” on the front panel. They are used to enable the 75-Ohm resistance video impedance. DIP switches should be turned to the “ON” position if cameras are connected to the video inputs. If users want to connect another device to the video output, such as a VCR or multiplexer, the switches should be turned to the “OFF” position to disable the impedance.

6: System LEDs: “POWER,” “CONNECT,” and “SERIAL”

Each time the Video Server starts up, it will perform a Power-On-Self-Test (POST) to examine each hardware module. VPort 2140 has 3 LEDs:

VPort 2140 User’s Manual 1-5

Image 11
Contents First Edition, March VPort User’s ManualDisclaimer Copyright NoticeTrademarks Before getting started Table of Contents Chapter Advanced Applications Page Introduction Overview Product Features Package ChecklistModem Dial-up Connection Typical ApplicationsEthernet Connection Front Panel Product DescriptionsName Description Work Status Mode ConditionNetwork LEDs ACTIVE, LINK, and FDX Pin description Regulation Rear PanelCOM1 & COM General I/O terminal blockInput 12 VDC 11 10/100 Mbps EthernetGetting Started Before Getting Started Setting up an Ethernet EnvironmentFront Panel Setting up an Ethernet EnvironmentBefore Getting Started Cable ConnectionRear Panel Running the IP Installer ProgramAssigning an IP Address to VPort 2140 Video Server Powering on the VPort 2140 Video ServerUsing the IP Installer Program Getting Started Using DOS Commands under Windows Accessing VPort 2140 Video Server for the First TimeNull Modem Setting up a Modem EnvironmentModem Powering on VPort 2140 Video ServerInstalling a new modem Configuring a Modem Under Windows 2000 EnvironmentVPort 2140 User’s Manual Modem Mode Click on Start Control Panel Modems Setting up a new connectionVPort 2140 User’s Manual Getting Started Panel Mounting Null Modem ModeModem Mode Mounting VPortAccessing VPort 2140 Video Server for the First Time Opening Your Browser Accessing VPort 2140 Video ServerAuthentication Image Mode Functions Featured on the MainInstalling the Plug-in Application Image Mode and Text ModeImage Size Selection Logo and Host NameVideo Quality Selection Relay Output Control System ConfigurationCustom Camera Commands Camera View selectionPage System Configuration Restore facotry default settings Reset system Using Setup Wizard System Configuration Via Web AccessSurveillance System Using the Application WizardSystem Host nameDate and Time Root passwordSecurity Add user Snapshot modeReset network at next boot NetworkHttp GeneralSave the modification FTPShow Time stamp in image and Text on image Image settingColor, Default size, and Default quality VideoCamera type Camera SettingPreset position setting of Motorized PTZ camera Motion DetectionRS-232 RS-485 Speed Default Video SourceCOM 1 & COM ModulationPurpose Interface modePort Settings Application Custom commandLevel Weekly scheduleTrigger Action Event operationShow alert in image Trigger ConditionSave Sequential ModeSend Snapshot by Email or FTP View SnapshotLogo graph DemoHomepage layout Background graph Web page display modeView log file Logo linkView parameters Factory defaultVideo Server Initial Configuration file System Configuration Via FTPFrom 12 to Lime, 10-aqua, 11-fuchsia, 12-silver Or 1024 to String of max characters Or RS485 Or YES to activate external script Monitor changed status of digital inputs System Configuration Via TelnetTelnet Commands System core debuggingReset system Skip installation at next bootReset network for new settings Restore factory default settingsAdvanced Applications URL Commands for DI/DO & Camera’s Actions SettingGetting snapshot via FTP Capturing Up-to-date Still ImagesVideo Embedded in Customers’ Homepage Getting snapshot via URLGetting triggered snapshots via FTP File name Pre-alarm Upon alarm Post-alarmDownload Event-triggered Snapshots Getting triggered snapshots via URLObject File name Maximal size Command Script for DI/DO & Camera’s Actions SettingCustomizing Graphics in Homepage Operator Command formatParameter Explanations EventPractical Examples Command line DescriptionRecalling camera position URL Commands for DI/DO & Camera’s Actions SettingDrive digital outputs Moving motorized camera in PTZ directionRestart System via URL URL Commands for System MaintenanceRestore Factory Default Settings via URL Download System Log via FTPUpgrading System Firmware Using Upgrade Wizard to Upgrade Firmware Easily Using FTP to Upgrade Firmware Page Troubleshooting LED pattern after Post Failed function Troubleshooting Power On Self Test PostFrequently Asked Questions Troubleshooting VPort 2140 User’s Manual URL URL Commands of Video ServerName Value Description Resource name Reference URLNetwork Configuration URL Video Configuration URL COM 1 Configuration URL Camera custom command configuration URL Custom camera configuration URL Motion detection configuration URL VPort 2140 User’s Manual A-9 Page Camera model Baud rate Data bits Stop bit Parity bit Settings of Supported PTZ CamerasPage Camera Control Cable Page Time Zone Table VPort 2140 User’s Manual Technical Specifications General I/O Service Information Following services are provided Moxa Internet ServicesMoxa Product VPort Serial Number Problem Report FormProduct Return Procedure