Moxa Technologies VPort 2140 user manual Event operation, Show alert in image, Trigger Condition

Page 49

System Configuration

Enable the external script file to exclude the following settings

Administrators can write a script named SCRIPT.TXT to match the additional software according to the Command Script for DI/DO and Camera’s Actions Setting section from Chapter 5. After uploading this script to the VPort via FTP, check the option Enable the external script file to exclude the following settings. Otherwise the VPort will operate according to the settings under Enable the external script file to exclude the following settings option.

Event operation

Event operation is for setting security applications.

1.Show alert in image.

VPort 2140 Video Server can show the event trigger condition in the video image on the homepage. If motion is detected (based on the motion settings), an M will appear on the upper-right corner of the image. As long as Show alert in image is checked, the M will appear in the image to indicate that motions have been detected. If there are any sensors attached to the digital inputs, the administrator can set the state to fire alarm.

The option Show alert in image may be set when running the application wizard or configuring motion detection. Administrators should manually uncheck this option if no indication of motion detection is needed in the image.

2.Trigger Condition

a.Motion Detected. The administrator can check the boxes of Video 1, Video 2, Video 3 and Video 4 to enable Video Motion Detection (VMD), which is set in the Video configuration web page (or you can click on the *Click on each hyperlink of video to configure motion detection link below to configure the appropriate parameters) as the trigger condition.

b.DI Condition. There are 4 Digit Inputs in VPort 2140. The administrator can set the DI’s conditions, including Input is High, Input is Low, Input is Rising, and Input is Falling. The edge trigger like Rising or Falling is generally used to detect the emerging signal from the external sensor.

3.Trigger Action

Once an event occurs, the administrator can set up 2 trigger actions: relay output alarms or snapshot image.

a.DO Action. There are 2 DOs (Relay output) for connecting the alarms. Administrators can set the trigger output alarm when the DI or Video Motion Detection conditions are met. Once an event occurs, the administrator can select the Delay second(s) after event option to drive a device attached to the digital outputs several seconds after the event happens and/or send snapshots that are taken right at the moment.

b.Snapshot. The administrator can set up the snapshot action when the DI or Video Motion Detection conditions are met. There are 3 snapshots will be taken when an event occurs, which is in the tenth second interval by named as pre-event, the moment of event and post-event. If the administrator thinks the snapshots are not enough, more snapshots can be taken after the event by configuring Take snapshot(s) with tenth seconds interval after the event. Three snapshots of each channel can also be downloaded via FTP or HTTP URL.The time interval of these 3 snapshot images can be set on (refer to the “Download Event-triggered Snapshots” section from Chapter 5 for more details).

c.Send snapshot while trigger condition(s) match. To activate the function of snapshot sent via E-mail or FTP server, this item should be checked.

VPort 2140 User’s Manual 4-15

Image 49
Contents First Edition, March VPort User’s ManualTrademarks Copyright NoticeDisclaimer Before getting started Table of Contents Chapter Advanced Applications Page Introduction Overview Product Features Package ChecklistEthernet Connection Typical ApplicationsModem Dial-up Connection Front Panel Product DescriptionsNetwork LEDs ACTIVE, LINK, and FDX Mode ConditionName Description Work Status COM1 & COM Rear PanelGeneral I/O terminal block Pin description RegulationInput 12 VDC 11 10/100 Mbps EthernetGetting Started Before Getting Started Setting up an Ethernet EnvironmentBefore Getting Started Setting up an Ethernet EnvironmentCable Connection Front PanelRear Panel Running the IP Installer ProgramUsing the IP Installer Program Powering on the VPort 2140 Video ServerAssigning an IP Address to VPort 2140 Video Server Getting Started Using DOS Commands under Windows Accessing VPort 2140 Video Server for the First TimeNull Modem Setting up a Modem EnvironmentModem Powering on VPort 2140 Video ServerInstalling a new modem Configuring a Modem Under Windows 2000 EnvironmentVPort 2140 User’s Manual Modem Mode Click on Start Control Panel Modems Setting up a new connectionVPort 2140 User’s Manual Getting Started Modem Mode Null Modem ModeMounting VPort Panel MountingAccessing VPort 2140 Video Server for the First Time Authentication Accessing VPort 2140 Video ServerOpening Your Browser Installing the Plug-in Application Functions Featured on the MainImage Mode and Text Mode Image ModeVideo Quality Selection Logo and Host NameImage Size Selection Custom Camera Commands System ConfigurationCamera View selection Relay Output ControlPage System Configuration Restore facotry default settings Reset system Using Setup Wizard System Configuration Via Web AccessSystem Using the Application WizardHost name Surveillance SystemSecurity Root passwordDate and Time Reset network at next boot Snapshot modeNetwork Add userHttp GeneralSave the modification FTPColor, Default size, and Default quality Image settingVideo Show Time stamp in image and Text on imagePreset position setting of Motorized PTZ camera Camera SettingMotion Detection Camera typeCOM 1 & COM Default Video SourceModulation RS-232 RS-485 SpeedPort Settings Interface modePurpose Application Custom commandLevel Weekly scheduleShow alert in image Event operationTrigger Condition Trigger ActionSend Snapshot by Email or FTP Sequential ModeView Snapshot SaveHomepage layout DemoLogo graph View log file Web page display modeLogo link Background graphView parameters Factory defaultVideo Server Initial Configuration file System Configuration Via FTPFrom 12 to Lime, 10-aqua, 11-fuchsia, 12-silver Or 1024 to String of max characters Or RS485 Or YES to activate external script Telnet Commands System Configuration Via TelnetSystem core debugging Monitor changed status of digital inputsReset network for new settings Skip installation at next bootRestore factory default settings Reset systemAdvanced Applications URL Commands for DI/DO & Camera’s Actions SettingVideo Embedded in Customers’ Homepage Capturing Up-to-date Still ImagesGetting snapshot via URL Getting snapshot via FTPDownload Event-triggered Snapshots File name Pre-alarm Upon alarm Post-alarmGetting triggered snapshots via URL Getting triggered snapshots via FTPCustomizing Graphics in Homepage Command Script for DI/DO & Camera’s Actions SettingObject File name Maximal size Parameter Explanations Command formatEvent OperatorPractical Examples Command line DescriptionDrive digital outputs URL Commands for DI/DO & Camera’s Actions SettingMoving motorized camera in PTZ direction Recalling camera positionRestore Factory Default Settings via URL URL Commands for System MaintenanceDownload System Log via FTP Restart System via URLUpgrading System Firmware Using Upgrade Wizard to Upgrade Firmware Easily Using FTP to Upgrade Firmware Page Troubleshooting Frequently Asked Questions Power On Self Test PostLED pattern after Post Failed function Troubleshooting Troubleshooting VPort 2140 User’s Manual URL URL Commands of Video ServerName Value Description Resource name Reference URLNetwork Configuration URL Video Configuration URL COM 1 Configuration URL Camera custom command configuration URL Custom camera configuration URL Motion detection configuration URL VPort 2140 User’s Manual A-9 Page Camera model Baud rate Data bits Stop bit Parity bit Settings of Supported PTZ CamerasPage Camera Control Cable Page Time Zone Table VPort 2140 User’s Manual Technical Specifications General I/O Service Information Following services are provided Moxa Internet ServicesMoxa Product VPort Serial Number Problem Report FormProduct Return Procedure