Moxa Technologies 5400 Series user manual Event Type, Snmp Trap Server

Page 54

NPort 5400 Series User’s Manual

Web Console Configuration

ATTENTION

Consult your Network Administrator or ISP for the proper mail server settings. Auto warning function may not work properly without proper settings. NPort SMTP AUTH supports LOGIN, PLAIN, CRAM-MD5 (RFC 2554).

SNMP Trap Server

SNMP trap server IP or domain name

Setting	Factory Default	Necessity
IP or Domain Name	None	Optional

Event Type

Cold start

This refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort will automatically issue an Auto warning message by e-mail, or send an SNMP trap after rebooting.

Warm start

This refers to restarting the computer without turning the power off. It’s the opposite of cold start. When performing a warm start, the NPort will automatically send an e-mail, or send an SNMP trap after rebooting.

Authentication failure

The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort will immediately send an e-mail or send an SNMP trap.

IP address changed

The user has changed the NPort’s IP address. When the IP address changes, the NPort will send an e-mail with the new IP address before the NPort reboots. If the NPort fails to send mail to the mail server after 15 seconds, the NPort will be rebooting directly and abort the mail auto warning.

5-28

Image 54

Contents NPort 5400 Series User’s Manual Sixth Edition, MarchCopyright Notice TrademarksDisclaimer Table of Contents Chapter IP Serial LIB Introduction Package Checklist Product FeaturesOverview Product Specifications Serial Communication Parameters Software FeaturesPower Requirements Mechanical‰ Panel Layout ‰ Connecting the Hardware Getting StartedPanel Layout NPort 5410/5450/5450INPort 5430/5430I Connecting the Power Connecting the HardwareWiring Requirements Grounding the NPortLED Indicators Connecting to the NetworkConnecting to a Serial Device LED Name LED Color LED FunctionAdjustable Pull High/low Resistors for the RS-485 Port Pull high/low resistors for the RS-485 PortInitial IP Address Configuration Initializing the NPort’s IP Address Factory Default IP AddressDefault IP address LCM DisplayButton Name Action Detailed Menu OptionsInact. time Delimiter NPort Administration Suite ARPTelnet Console Page Page Choosing the Proper Operation Mode Real COM Mode TCP Server Mode TCP Client Mode UDP ModePair Connection Mode Reverse Telnet Mode Disabled ModeWeb Console Configuration Opening Your Browser NPort 5400 Series User’s Manual Web Console Configuration Server name Basic SettingsTime Time zoneTime server LCM password protectWeb/Telnet Console Web consoleNetwork Settings Reset button protectMethod Function Definition Netmask IP ConfigurationIP Address GatewaySnmp Settings IP Address ReportAuto report to IP Serial SettingsSetting Factory Default Necessity 4002 Optional Auto report to UDP portSerial Parameters Operating Settings Real COM ModeInterface Max Connection 2 to Max ConnectionMax. Connection Ignore jammed IPDelimiter Setting Factory Default Necessity To FF None OptionalSetting Factory Default Necessity To 65535 ms Optional Delimiter processTCP alive check time TCP Server ModeSetting Factory Default Necessity To 99 min Min Optional Inactivity timeAllow driver control Delimiter Command port TCP Client ModeSetting Factory Default Necessity 4001 Required Setting Factory Default Necessity 966 OptionalNPort 5400 Series User’s Manual Web Console Configuration Delimiter Designated Local Port 1/2/3/4 Destination IP addressDestination IP address 2/3/4 Connection controlUDP Mode Connect/Disconnect DescriptionDelimiter process Pair Connection Mode Pair Connection Master ModeLocal listen port Pair Connection Slave Mode Setting Factory Default Necessity To 99 min Min RequiredSetting Factory Default Necessity 4001 Optional Reverse Telnet ModeSetting Factory Default Necessity To 99 min Optional Means it will never disconnectOnly one host of specific IP address can access the NPort Accessible IP SettingsDisabled Mode Hosts on the specific subnet can access the NPortAuto Warning Settings Auto warning E-mail and Snmp trapMail Server Event Type Snmp Trap ServerDSR changed Password changedDCD changed MailMonitor Line Monitor Async-SettingsMonitor Monitor AsyncChange Password Load Factory DefaultConfiguring NPort Administrator ‰ Overview ‰ Installing NPort Administrator ‰ ConfigurationInstalling NPort Administrator Page Page Configuration Broadcast Search Specify by IP AddressPassword Protection Unlock Password ProtectionConfiguring the NPort Page Page Web Console Upgrading the FirmwarePage Export Configuration Import ConfigurationBroadcast Search Æ Monitor Æ Add Target Monitor Æ Add Target Æ Rescan Monitor Æ Load Configured COM Port Once the Monitor function is runningPage Page Page Port Monitor COM Mapping On-line COM MappingPage Fast Flush only flush local buffer Page Page Off-line COM Mapping Page IP Address Report Automatic Message Log IP Serial LIB What is IP Serial Library? Why Use IP Serial Library?How to install IP Serial Library? Server Control IP Serial LIB Function GroupsExample Program Port Control Input/Output Data Port Status MiscellaneousPinouts and Cable Wiring Port Pinout Diagrams Ethernet Port Pinouts Serial Port PinoutsCable Wiring Diagrams Ethernet Cables Serial CablesDB9 Female to DB9 Male for NPort DB9 Female to DB25 Male for NPort TCP Socket Application Service Well Known Port NumbersUDP Socket Application Service NPort 5400 Series User’s Manual Well Known Port NumbersSnmp Agents with MIB II & RS-232 like group IP MIB Icmp MIBSystem MIB Interfaces MIB Address Translation MIBInput Signal Table Output Signal Table TCP MIB Snmp MIBAuto IP Report Protocol ID List Auto IP Report FormatInfo n AP ID & Hardware ID Mapping TableService Information Moxa Internet Services Following services are providedProblem Report Form Moxa Product† NPortSerial Number Product Return Procedure