Moxa Technologies user manual NPort 5400 Series User’s Manual Web Console Configuration

Page 44

NPort 5400 Series User’s Manual

Web Console Configuration

 

TCP alive check time

 

 

 

 

Setting

Factory Default

Necessity

 

 

0 to 99 min

7 min

Optional

 

 

 

 

 

 

0 min: TCP connection is not closed due to an idle TCP connection.

1 to 99 min: The NPort automatically closes the TCP connection if there is no TCP activity for the given time.

Inactivity time

Setting

Factory Default

Necessity

0 to 65535 ms

0 ms

Optional

 

 

 

0 ms: TCP connection is not closed due to an idle serial line.

0-65535 ms: The NPort automatically closes TCP connection, if there is no serial data activity for the given time.

This parameter defines the maintenances status as Closed or Listen on the TCP connection. The connection is closed if there is no incoming or outgoing data through the serial port during the specific Inactivity time.

If the value of inactivity time is set to 0, the current TCP connection is maintained until there’s connection close request. Although the inactivity time is disabled, the NPort will check the connection status between the NPort and remote host by sending “keep alive” packets periodically. If the remote host does not respond to the packets, it treats the connection as being down unintentionally. The NPort will then force the existing TCP connection to close.

ATTENTION

The Inactivity time should at least be set larger than that of Force transmit timeout. To prevent the unintended loss of data due to the session being disconnected, it is highly recommended that this value is set large enough so that the intended data transfer is completed.

ATTENTION

Inactivity time is ONLY active when “TCP connect on” is set to “Any character.”

Ignore jammed IP

Setting

Factory Default

Necessity

No or Yes

No

Optional

 

 

 

Previously, when Max connections > 1, and the serial device is transmitting data, if any one of the connected hosts is not responding, it will wait until the data has been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for “Ignore jammed IP,” the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.

Packing length

Setting

Factory Default

Necessity

0 to 1024

0

Optional

 

 

 

Default = 0, The Delimiter Process will be followed, regardless of the length of the data packet. If the data length (in bytes) matches the configured value, the data will be forced out. The data length

5-18

Page 43 Page 45
Image 44
Page 43 Page 45
Contents NPort 5400 Series User’s Manual Sixth Edition, MarchDisclaimer Copyright NoticeTrademarks Table of Contents Chapter IP Serial LIB Introduction Overview Package ChecklistProduct Features Product Specifications Software Features Power RequirementsSerial Communication Parameters Mechanical‰ Panel Layout ‰ Connecting the Hardware Getting StartedNPort 5430/5430I Panel LayoutNPort 5410/5450/5450I Connecting the Hardware Wiring RequirementsConnecting the Power Grounding the NPortConnecting to the Network Connecting to a Serial DeviceLED Indicators LED Name LED Color LED FunctionAdjustable Pull High/low Resistors for the RS-485 Port Pull high/low resistors for the RS-485 PortInitial IP Address Configuration Factory Default IP Address Default IP addressInitializing the NPort’s IP Address LCM DisplayButton Name Action Detailed Menu OptionsInact. time Delimiter NPort Administration Suite ARPTelnet Console Page Page Choosing the Proper Operation Mode Real COM Mode TCP Server Mode Pair Connection Mode TCP Client ModeUDP Mode Reverse Telnet Mode Disabled ModeWeb Console Configuration Opening Your Browser NPort 5400 Series User’s Manual Web Console Configuration Basic Settings TimeServer name Time zoneLCM password protect Web/Telnet ConsoleTime server Web consoleMethod Function Definition Network SettingsReset button protect IP Configuration IP AddressNetmask GatewaySnmp Settings IP Address ReportSerial Settings Setting Factory Default Necessity 4002 OptionalAuto report to IP Auto report to UDP portSerial Parameters Interface Operating SettingsReal COM Mode Max Connection Max. ConnectionMax Connection 2 to Ignore jammed IPSetting Factory Default Necessity To FF None Optional Setting Factory Default Necessity To 65535 ms OptionalDelimiter Delimiter processTCP Server Mode Setting Factory Default Necessity To 99 min Min OptionalTCP alive check time Inactivity timeAllow driver control Delimiter TCP Client Mode Setting Factory Default Necessity 4001 RequiredCommand port Setting Factory Default Necessity 966 OptionalNPort 5400 Series User’s Manual Web Console Configuration Delimiter Destination IP address Destination IP address 2/3/4Designated Local Port 1/2/3/4 Connection controlUDP Mode Connect/Disconnect DescriptionDelimiter process Local listen port Pair Connection ModePair Connection Master Mode Pair Connection Slave Mode Setting Factory Default Necessity To 99 min Min RequiredReverse Telnet Mode Setting Factory Default Necessity To 99 min OptionalSetting Factory Default Necessity 4001 Optional Means it will never disconnectAccessible IP Settings Disabled ModeOnly one host of specific IP address can access the NPort Hosts on the specific subnet can access the NPortMail Server Auto Warning SettingsAuto warning E-mail and Snmp trap Event Type Snmp Trap ServerPassword changed DCD changedDSR changed MailMonitor Async-Settings MonitorMonitor Line Monitor AsyncChange Password Load Factory DefaultConfiguring NPort Administrator ‰ Overview ‰ Installing NPort Administrator ‰ ConfigurationInstalling NPort Administrator Page Page Configuration Broadcast Search Specify by IP AddressPassword Protection Unlock Password ProtectionConfiguring the NPort Page Page Web Console Upgrading the FirmwarePage Export Configuration Import ConfigurationBroadcast Search Æ Monitor Æ Add Target Monitor Æ Add Target Æ Rescan Monitor Æ Load Configured COM Port Once the Monitor function is runningPage Page Page Port Monitor COM Mapping On-line COM MappingPage Fast Flush only flush local buffer Page Page Off-line COM Mapping Page IP Address Report Automatic Message Log IP Serial LIB How to install IP Serial Library? What is IP Serial Library?Why Use IP Serial Library? IP Serial LIB Function Groups Example ProgramServer Control Port Control Input/Output Data Port Status MiscellaneousPinouts and Cable Wiring Port Pinout Diagrams Ethernet Port Pinouts Serial Port PinoutsDB9 Female to DB9 Male for NPort Cable Wiring DiagramsEthernet Cables Serial Cables DB9 Female to DB25 Male for NPort TCP Socket Application Service Well Known Port NumbersUDP Socket Application Service NPort 5400 Series User’s Manual Well Known Port NumbersSnmp Agents with MIB II & RS-232 like group IP MIB Icmp MIBSystem MIB Interfaces MIB Address Translation MIBInput Signal Table Output Signal Table TCP MIB Snmp MIBAuto IP Report Protocol Auto IP Report Format Info nID List AP ID & Hardware ID Mapping TableService Information Moxa Internet Services Following services are providedSerial Number Problem Report FormMoxa Product† NPort Product Return Procedure
Top Page Image Contents