Paradyne BitStorm 2600 manual GigE Uplink Port

Page 25

2. Cabling

4. Tighten the cable tie around the connector and trim the excess.

02-17084

5.If you use an internal POTS splitter, repeat Step 1 through Step 4, substituting POTS 1–24 for DSL PORTS 1–24.

6.Secure the cables as required for strain relief.

GigE Uplink (Port 3)

Port 3 comprises two interfaces, only one of which may be used at a time:

„An 8-position modular jack providing support for 1000BaseT

„A Small Form-Factor Pluggable (SFP) socket providing, with the appropriate transceiver installed, support for 1000BaseX. A single-mode 1000BaseLX transceiver is available from Paradyne. See Appendix B, Equipment List.

Either interface can be used as the uplink for a single BitStorm 2600, or for the terminating unit in a stack of BitStorm 2600s.

Procedure

To use Port 3 as the uplink:

1.Connect the uplink cable to the BitStorm 2600:

For a wire connection, plug the 8-position modular plug of your uplink cable into the Port 3 1000BT modular jack. A straight-through cable can be used regardless of the destination interface, since the port automatically distinguishes between a Medium-Dependent Interface (MDI) and an MDI Crossover (MDIX).

For a fiber connection, plug your transceiver into the Port 3 GigE SFP socket. Plug the LC connector of your fiber optic uplink cable into the cable socket of the transceiver. Observing the minimum bend radius for your cable, fasten it with cable ties in such a way that it will not be kinked or snagged in the course of other cabling. If you do not know the specifications for your cable, maintain a radius of at least ten times the cable diameter.

2600-A2-GN20-40

March 2005

2-3

Image 25
Contents IP Dslam Copyright 2005 Paradyne Corporation All rights reserved Software and Firmware License Agreement Important Safety Instructions United States EMI Notice Japan Contents Connectors and Pin Assignments ConfigurationEquipment List Technical Specifications Index LEDsDocument Purpose and Intended Audience About This GuideDocument Summary Document Number Document Title Related Product DocumentsOverview InstallationPreparation „ Installation SiteDSL Ports Cables RequiredUnpacking the Hardware Package ContentsFlat-head screw for attaching 19 mounting brackets to Installing the Brackets for Rack Mounting Mounting ConfigurationsMounting Brackets Inch 483 mm Rack Mount Installing the BitStorm 2600 Into a Rack 03-17436 Installing the BitStorm 2600 on a Wall 17.85 in 453 mm Installing the BitStorm 2600 on a Shelf or Desktop Cabling Overview CablingDSL Ports GigE Uplink Port 10/100BaseT Uplink Port T1 or E1 Uplink Chaining BitStorm 2600s Management Port Console Port Connecting a Terminal or PC to the Console PortConnecting a Modem to the Console Port Alarm Interface Ground Connecting to Power LED Locations LEDsLED LED MeaningsConfiguration CLI Commands Function Using the CLIConfigure Management Inband Address Login BitStorm 2600 Startup ProcedureStartup Procedure for Out-of-Band Management Startup Procedure for Inband ManagementUsing the Web Interface System / Users Configuration / Management / Snmp Figure A-1. BitStorm 2600 IP Front Panel Connectors and Pin AssignmentsDSL Ports and Pots Splitter Connectors Port 3 1000BaseT Connector Port 1 and Port 2 10/100BaseT ConnectorsTable A-4. Port 3 GigE Connector Signal Pin Port 3 GigE SFP ConnectorConsole Port Connector E1 and T1 Uplink ConnectorsTable A-7. Alarm Connections Signal Direction Contact Alarm ConnectorDSL Equipment ListTable B-1. BitStorm 2600 Model List 2 DSL Technical SpecificationsTable C-1. BitStorm 2600 Technical Specifications 2 Criteria Numerics IndexIN-2 IN-3 IN-4