Paradyne BitStorm 2600 manual United States EMI Notice

Page 5

13.The power supply cord for countries other than North America is to be a minimum H05 V V-F type, min. 0.75 mm2, 2-conductor and earth ground terminated in an IEC 320 connector on one end, and a plug which is certified for use in the country of installation at the other end.

14.Do not physically stack more than eight (8) 26x1 units high. Physical stability has not been evaluated for stacking higher than eight units, and any configuration greater than eight may result in an unstable (tip-over) condition. Ensure that the four (4) rubber feet supplied with the product have been installed on the bottom of each unit prior to stacking any 26x1 units on top of one another.

EMI Notices

!UNITED STATES – EMI NOTICE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements that no modifications will be made to the equipment unless the changes or modifications are expressly approved by Paradyne Corporation.

If the equipment includes a ferrite choke or chokes, they must be installed per the installation instructions.

!CANADA – EMI NOTICE:

This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du réglement sur le matérial brouilleur du Canada.

Notices to Users of the Canadian Telephone Network

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment and includes the effect of the POTS splitter. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.

When the equipment is used in a customer premises environment, a Model 6051 POTS Splitter must be used to ensure CS-03 compliance. Refer to the POTS splitter installation instructions for details.

CE Marking

When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library Technical Manuals CE Declarations of Conformity.

2600-A2-GN20-40

March 2005

D

Image 5
Contents IP Dslam Copyright 2005 Paradyne Corporation All rights reserved Software and Firmware License Agreement Important Safety Instructions United States EMI Notice Japan Contents Connectors and Pin Assignments ConfigurationEquipment List Technical Specifications Index LEDsDocument Summary About This GuideDocument Purpose and Intended Audience Document Number Document Title Related Product DocumentsOverview InstallationPreparation „ Installation SiteDSL Ports Cables RequiredUnpacking the Hardware Package ContentsFlat-head screw for attaching 19 mounting brackets to Mounting Brackets Mounting ConfigurationsInstalling the Brackets for Rack Mounting Inch 483 mm Rack Mount Installing the BitStorm 2600 Into a Rack 03-17436 Installing the BitStorm 2600 on a Wall 17.85 in 453 mm Installing the BitStorm 2600 on a Shelf or Desktop Cabling Overview CablingDSL Ports GigE Uplink Port 10/100BaseT Uplink Port T1 or E1 Uplink Chaining BitStorm 2600s Management Port Console Port Connecting a Terminal or PC to the Console PortConnecting a Modem to the Console Port Alarm Interface Ground Connecting to Power LED Locations LEDsLED LED MeaningsConfiguration CLI Commands Function Using the CLIConfigure Management Inband Address Login BitStorm 2600 Startup ProcedureStartup Procedure for Out-of-Band Management Startup Procedure for Inband ManagementUsing the Web Interface System / Users Configuration / Management / Snmp Figure A-1. BitStorm 2600 IP Front Panel Connectors and Pin AssignmentsDSL Ports and Pots Splitter Connectors Port 3 1000BaseT Connector Port 1 and Port 2 10/100BaseT ConnectorsTable A-4. Port 3 GigE Connector Signal Pin Port 3 GigE SFP ConnectorConsole Port Connector E1 and T1 Uplink ConnectorsTable A-7. Alarm Connections Signal Direction Contact Alarm ConnectorDSL Equipment ListTable B-1. BitStorm 2600 Model List 2 DSL Technical SpecificationsTable C-1. BitStorm 2600 Technical Specifications 2 Criteria Numerics IndexIN-2 IN-3 IN-4