TP-Link TD-8816 manual Snmp, ADSL2+ Modem Router User Guide, To add a URL filter entry

Page 55
To add a URL filter entry:

TD-8816

ADSL2+ Modem Router User Guide

Figure 4-38

Filter Type Selection: Select the URL Filter for the next configuration.

Active: Select “Yes” to make the rule take effect.

URL Index: Select the index for the URL Filter entry.

URL: Enter the URL for this URL Filter.

URL Filter Listing: This displays the information about the URL Filter rules.

To add a URL filter entry:

For example: If you want to forbid the user to access the website: www.yahoo.com. Presume the rule is aimed at the interface PVC0, and its index is “1”.

Step 1: Select the “URL Filter” as the Filter Type Selection (show in Figure 4-38).

Step 2: Select the Index for the rule, and then enter the website in the URL field.

Step 3: Finally, Select Yes to active the rule, and then click the SAVE button to save the entry.

Other configurations for the entries as shown in Figure 4-36:

Enter the URL Index to view or modify the entry.

Enter the URL Index to locate the specific rule, and then click the DELETE button to delete the entry.

4.5.3 SNMP

Choose “Access ManagementSNMP”, you can see the SNMP screen( shown in Figure 4-39). The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices.

48

Image 55
Contents Rev3.1.0 1910010870 TD-8816 ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTSafety Information The product carries the CE Mark DECLARATION OF CONFORMITYEN EN EN 61000-3-22006+A12009+A22009 EN EN 60950-12006+A11:2009+A12010+A122011Chapter 3. Quick Installation Guide CONTENTSPackage Contents Hardware InstallationAppendix D Technical Support AppendixA SpecificationsAppendix B Configuring the PC Appendix C Troubleshooting Note Package ContentsTD-8816 ADSL2+ Modem Router User GuideADSL 1.2 Main FeaturesChapter 1. Introduction 1.1 Product Overview1.3 Conventions Name Chapter 2. Hardware Installation2.1 The Front Panel LED Explanation2.2 The Back Panel 2.3 Installation Environment2.4 Connecting the Router Step 4 Turn on the TD-8816 and power on the computers and LAN devices 3.1 TCP/IP Configuration Chapter 3. Quick Installation Guide192.168.1.1 3.2 Login2 Is the TCP/IP configuration for your PC correct? 1 Is the connection between your PC and the modem router correct?Click the NEXT button Step 5 Click NEXT to finish the Quick Start 4.1 Status Chapter 4. Software Configuration4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics Statistics Table  Select Ethernet, and you will see the statistics table as below Select ADSL, and you will see the statistics table as below 4.2 Quick Start 4.3 Interface Setup4.3.1 Internet ∙ Virtual Circuit Select the VC number you want to setup, PVC0~PVC7 4.3.1.1. IPv4 ∙ VCI Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 1 to 31 is reserved for well-known protocols. Please input the value provided by your ISP1. Dynamic IP Address 2. Static IP Address  TCP MTU Option Enter the TCP MTU as your desire. The default value is3. PPPoA/PPPoE  NoteADSL2+ Modem Router User Guide 4.3.1.2. IPv6 4. Bridge ModeADSL2+ Modem Router User Guide Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon xxxxxxxx. The modem router will not accept the IP address if it is not in this format ADSL2+ Modem Router User Guide 4.3.1.3. IPv4/IPv6 4.3.2 LAN Router Local IP These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet ∙ IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3 NAT 4.4.3.2. Virtual Server 4.4.3.1. DMZTo add a virtual server entry Other configurations for the entries as shown in Figure4.4.3.3. IP Address Mapping Click the BACK button to return to the previous screenTo add a mapping rule 4.4.4 QoS QoS Select this option to Activate/Deactivate the QoS ADSL2+ Modem Router User Guide 5. Define VLAN Group 4.4.5 VLAN6. Assign VLAN PVID for each Interface  VLAN ID This indicates the VLAN group4.4.6 ADSL 4.5 Access Management4.5.1 ACL 4.5.2.1. IP Filter 4.5.2 Filter Interface Select the interface for the entry To add an IP Address filtering entry  Rule Type For IP Filter, please select IP here4.5.2.2. MAC Filter To add a MAC Address filtering entry 4.5.2.3. Application Filter 4.5.2.4. URL Filter  Application Filter Activate or deactivate the functionTo add a URL filter entry 4.5.3 SNMP4.5.4 UPnP 4.5.6 CWMP 4.5.5 DDNS4.6.1 Administration 4.6 Maintenance1. NTP Server automatically 4.6.2 Time Zone2. PC’s Clock 4.6.3 Firmware3. Manually To back up the Router’s current settings 4 The modem router will reboot after the upgrading has been finishedTo restore the modem router’s settings 4.6.4 SysRestart4.7 Help 4.6.5 DiagnosticsADSL2+ Modem Router User Guide General AppendixA SpecificationsPhysical and Environment 1. Configure TCP/IP component Appendix B Configuring the PCFigure B-1 shown in the Figure below Now you have two ways to configure the TCP/IP protocol below Setting IP address automatically Figure B-2Figure B-3  Setting IP address manuallyFigure B-4 Now Click OK to keep your settingsb Go to “System Preferences - Network” Appendix C TroubleshootingT2. What can I do if I don’t know or forgot my password? For Mac OSClick Internet Options Select Never dial a connection b Click “View network status and tasks Change adapter settings” Note T4. What can I do if I cannot access the Internet?Appendix D Technical Support Technical Support
Related manuals
Manual 67 pages 35.92 Kb Manual 55 pages 18.54 Kb Manual 54 pages 55.13 Kb