TP-Link TD-8816 manual Package Contents, Chapter, Introduction, Hardware Installation

Page 6

 

 

CONTENTS

 

Package Contents

1

Chapter 1.

Introduction

2

1.1

Product Overview

2

1.2

Main Features

2

1.3

Conventions

3

Chapter 2.

Hardware Installation

4

2.1

The Front Panel

4

2.2

The Back Panel

5

2.3

Installation Environment

5

2.4

Connecting the Router

6

Chapter 3. Quick Installation Guide

8

3.1

TCP/IP Configuration

8

3.2

Login

9

Chapter 4.

Software Configuration

12

4.1

Status

12

 

4.1.1

Device Info

12

 

4.1.2

System Log

13

 

4.1.3

Statistics

14

4.2

Quick Start

16

4.3

Interface Setup

16

 

4.3.1

Internet

16

 

4.3.2

LAN

26

4.4

Advanced Setup

30

 

4.4.1

Firewall

30

 

4.4.2

Routing

30

 

4.4.3

NAT

31

 

4.4.4

QoS

35

 

4.4.5

VLAN

38

 

4.4.6

ADSL

40

4.5

Access Management

40

 

4.5.1

ACL

40

 

4.5.2

Filter

41

 

4.5.3

SNMP

48

 

4.5.4

UPnP

49

 

4.5.5

DDNS

50

Page 5 Page 7
Image 6
Page 5 Page 7
Contents TD-8816 ADSL2+ Modem Router Rev3.1.0 1910010870COPYRIGHT & TRADEMARKS FCC STATEMENT CE Mark WarningSafety Information EN 60950-12006+A11：2009+A12010+A122011 DECLARATION OF CONFORMITYEN EN EN 61000-3-22006+A12009+A22009 EN The product carries the CE MarkHardware Installation CONTENTSPackage Contents Chapter 3. Quick Installation GuideAppendix C Troubleshooting AppendixA SpecificationsAppendix B Configuring the PC Appendix D Technical SupportADSL2+ Modem Router User Guide Package ContentsTD-8816  Note1.1 Product Overview 1.2 Main FeaturesChapter 1. Introduction ADSL1.3 Conventions LED Explanation Chapter 2. Hardware Installation2.1 The Front Panel Name2.3 Installation Environment 2.2 The Back Panel2.4 Connecting the Router Step 4 Turn on the TD-8816 and power on the computers and LAN devices Chapter 3. Quick Installation Guide 3.1 TCP/IP Configuration1 Is the connection between your PC and the modem router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? 192.168.1.1Click the NEXT button Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics  Select Ethernet, and you will see the statistics table as below Statistics Table Select ADSL, and you will see the statistics table as below 4.3 Interface Setup 4.2 Quick Start4.3.1 Internet ∙ Virtual Circuit Select the VC number you want to setup, PVC0~PVC7 ∙ VCI Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 1 to 31 is reserved for well-known protocols. Please input the value provided by your ISP 4.3.1.1. IPv41. Dynamic IP Address  TCP MTU Option Enter the TCP MTU as your desire. The default value is 2. Static IP Address Note 3. PPPoA/PPPoETD-8816 4. Bridge Mode 4.3.1.2. IPv6TD-8816 Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon xxxxxxxx. The modem router will not accept the IP address if it is not in this format TD-8816 4.3.2 LAN 4.3.1.3. IPv4/IPv6 Router Local IP These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet ∙ IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1. DMZ 4.4.3.2. Virtual ServerOther configurations for the entries as shown in Figure To add a virtual server entryClick the BACK button to return to the previous screen 4.4.3.3. IP Address Mapping4.4.4 QoS To add a mapping rule QoS Select this option to Activate/Deactivate the QoS TD-8816 4.4.5 VLAN 5. Define VLAN Group VLAN ID This indicates the VLAN group 6. Assign VLAN PVID for each Interface4.5 Access Management 4.4.6 ADSL4.5.1 ACL 4.5.2 Filter 4.5.2.1. IP Filter Interface Select the interface for the entry  Rule Type For IP Filter, please select IP here To add an IP Address filtering entry4.5.2.2. MAC Filter To add a MAC Address filtering entry 4.5.2.3. Application Filter  Application Filter Activate or deactivate the function 4.5.2.4. URL Filter4.5.3 SNMP To add a URL filter entry4.5.4 UPnP 4.5.5 DDNS 4.5.6 CWMP4.6 Maintenance 4.6.1 Administration4.6.2 Time Zone 1. NTP Server automatically4.6.3 Firmware 2. PC’s Clock3. Manually 4 The modem router will reboot after the upgrading has been finished To back up the Router’s current settings4.6.4 SysRestart To restore the modem router’s settings4.6.5 Diagnostics 4.7 HelpTD-8816 AppendixA Specifications GeneralPhysical and Environment Appendix B Configuring the PC 1. Configure TCP/IP componentFigure B-1 Figure B-2 Now you have two ways to configure the TCP/IP protocol below Setting IP address automatically shown in the Figure below Setting IP address manually Figure B-3Click OK to keep your settings Figure B-4 NowFor Mac OS Appendix C TroubleshootingT2. What can I do if I don’t know or forgot my password? b Go to “System Preferences - Network”b Click “View network status and tasks Change adapter settings” Click Internet Options Select Never dial a connectionT4. What can I do if I cannot access the Internet?  NoteAppendix D Technical Support Technical Support
Related manuals
Manual 67 pages 35.92 Kb Manual 55 pages 18.54 Kb Manual 54 pages 55.13 Kb
Top Page Image Contents