TP-Link TD-8816 ADSL2+ Modem Router User Guide, Figure B-4 Now, Click OK to keep your settings

Page 69

Figure B-4

TD-8816

ADSL2+ Modem Router User Guide

Figure B-4

Now:

Click OK to keep your settings.

62

Image 69

Contents Rev3.1.0 1910010870 TD-8816 ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTSafety Information EN EN EN 61000-3-22006+A12009+A22009 EN DECLARATION OF CONFORMITYEN 60950-12006+A11：2009+A12010+A122011 The product carries the CE MarkPackage Contents CONTENTSHardware Installation Chapter 3. Quick Installation GuideAppendix B Configuring the PC AppendixA SpecificationsAppendix C Troubleshooting Appendix D Technical SupportTD-8816 Package ContentsADSL2+ Modem Router User Guide  NoteChapter 1. Introduction 1.2 Main Features1.1 Product Overview ADSL1.3 Conventions 2.1 The Front Panel Chapter 2. Hardware InstallationLED Explanation Name2.2 The Back Panel 2.3 Installation Environment2.4 Connecting the Router Step 4 Turn on the TD-8816 and power on the computers and LAN devices 3.1 TCP/IP Configuration Chapter 3. Quick Installation Guide2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the modem router correct? 192.168.1.1Click the NEXT button Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics  Select Ethernet, and you will see the statistics table as below Statistics Table Select ADSL, and you will see the statistics table as below 4.3 Interface Setup 4.2 Quick Start4.3.1 Internet ∙ Virtual Circuit Select the VC number you want to setup, PVC0~PVC7 ∙ VCI Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 1 to 31 is reserved for well-known protocols. Please input the value provided by your ISP 4.3.1.1. IPv41. Dynamic IP Address 2. Static IP Address  TCP MTU Option Enter the TCP MTU as your desire. The default value is3. PPPoA/PPPoE  NoteADSL2+ Modem Router User Guide 4.3.1.2. IPv6 4. Bridge ModeTD-8816 Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon xxxxxxxx. The modem router will not accept the IP address if it is not in this format ADSL2+ Modem Router User Guide 4.3.1.3. IPv4/IPv6 4.3.2 LAN Router Local IP These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet ∙ IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.2. Virtual Server 4.4.3.1. DMZTo add a virtual server entry Other configurations for the entries as shown in Figure4.4.3.3. IP Address Mapping Click the BACK button to return to the previous screenTo add a mapping rule 4.4.4 QoS QoS Select this option to Activate/Deactivate the QoS ADSL2+ Modem Router User Guide 5. Define VLAN Group 4.4.5 VLAN6. Assign VLAN PVID for each Interface  VLAN ID This indicates the VLAN group4.5 Access Management 4.4.6 ADSL4.5.1 ACL 4.5.2.1. IP Filter 4.5.2 Filter Interface Select the interface for the entry To add an IP Address filtering entry  Rule Type For IP Filter, please select IP here4.5.2.2. MAC Filter To add a MAC Address filtering entry 4.5.2.3. Application Filter 4.5.2.4. URL Filter  Application Filter Activate or deactivate the functionTo add a URL filter entry 4.5.3 SNMP4.5.4 UPnP 4.5.6 CWMP 4.5.5 DDNS4.6.1 Administration 4.6 Maintenance1. NTP Server automatically 4.6.2 Time Zone4.6.3 Firmware 2. PC’s Clock3. Manually To back up the Router’s current settings 4 The modem router will reboot after the upgrading has been finishedTo restore the modem router’s settings 4.6.4 SysRestart4.7 Help 4.6.5 DiagnosticsTD-8816 AppendixA Specifications GeneralPhysical and Environment Appendix B Configuring the PC 1. Configure TCP/IP componentFigure B-1  Setting IP address automatically Now you have two ways to configure the TCP/IP protocol belowFigure B-2 shown in the Figure belowFigure B-3  Setting IP address manuallyFigure B-4 Now Click OK to keep your settingsT2. What can I do if I don’t know or forgot my password? Appendix C TroubleshootingFor Mac OS b Go to “System Preferences - Network”Click Internet Options Select Never dial a connection b Click “View network status and tasks Change adapter settings” Note T4. What can I do if I cannot access the Internet?Appendix D Technical Support Technical Support

Related manuals

Manual 67 pages 35.92 Kb

Manual 55 pages 18.54 Kb

Manual 54 pages 55.13 Kb