TP-Link TL-WA5110G manual Wireless Mode

Page 30

The device will reboot automatically after you click the Save button.

Figure 4-11 Wireless Settings in AP Client Router mode

¾SSID - Enter a value of up to 32 characters. The same name (SSID) must be assigned to all wireless devices in your network. The default SSID is TP-LINK_xxxxxx (xxxxxx indicates the last six unique characters of each device’s MAC address). This value is case-sensitive. For example, TP-LINKis NOT the same as tp-link.

¾Region-Select your region from the drop-down list. This filed specifies the region where the wireless function of the device can be used. It may be illegal to use the wireless function of the device in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.

¾Channel – This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice problems with another nearby access point.

¾Mode - Select the desired wireless mode. The options are:

•54Mbps (802.11g) - Both 802.11g and 802.11b wireless stations can connect to the router.

•11Mbps (802.11b) - Only 802.11b wireless stations can connect to the router.

Be sure to click the Save button to save your settings on this page.

)Note:

The device will reboot automatically after you click the Save button.

4.6.2 Wireless Mode

This page allows you to configure the wireless mode for your device:

22

Image 30

Contents TL-WA5110G 54M High Power Wireless Access Point 1910010154COPYRIGHT & TRADEMARKS All rights reservedFCC STATEMENT FCC RF Radiation Exposure StatementCE Mark Warning National Restrictions 2400.0-2483.5 MHz General authorization required for outdoor useand public service CountryETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006 Product Description 54 M High Power Wireless Access PointETSI EN 300 328 V1.7.1 EN623112008CONTENTS Configuring the Device in AP Operation Mode 5.6.1 Package Contents 1.2 Features Chapter 1. Product Overview1.1 Overview of the Product 1.3 Conventions 2.2. The Rear Panel Chapter 2. Hardware Installation2.1. The Front Panel Indication2.3. System Requirements 2.5. Connecting the DeviceEnsure the AP is powered on before it restarts completely 2.4. Environment Requirements3. Connect the AP to the desktop PC Chapter 3. Quick Installation Guide 3.1. Configure the DeviceFor Windows 98 OS or earlier, the PC and AP may need to be restarted 3.2. Quick Setup Please check the connection following these stepsFigure 3-4 Login Windows Figure 3-7 Choose WAN Connection Type The IP parameters should have been provided by your ISP Figure 3-9 Quick Setup - Static IPFigure 3-11 Quick Setup - Wireless settings 4.1 Login 4.2 Status1. LAN IP address and Subnet Mask 2. WirelessSSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN 4. Traffic Statistics4.5 Network 4.3 Quick Setup4.4 Operation Mode 4.5.1 LAN4.5.2 WAN Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP You should type the following parameters into the spaces providedFigure 4-7 WAN - PPPoE 4.5.3 MAC Clone 1 Only the PC on your LAN can use the Clone MAC Address To feature 4.6 Wireless4.6.1 Basic Settings 2 If you click Save, the router will prompt you to reboot4.6.2 Wireless Mode The device will reboot automatically after you click the Save buttonFigure 4-12 Wireless Mode Figure 4-13 AP List 4.6.3 Security Settings Figure 4-14 Wireless Mode settings in AP Router modeYou can select one of the following security options 3. Open System - Select 802.11 Open System authentication Figure 4-15 Wireless Security2. Shared Key - Select 802.11 Shared Key authentication ¾ WEP - Select 802.11 WEP security4.6.4 MAC Filtering ¾ Description - A simple description of the wireless station Figure 4-16 Wireless MAC address Filtering¾ Status - The status of this entry either Enabled or Disabled To set up an entry, follow these instructions6. Click the Save button to save this entry 4.6.5 Wireless Statistics 4.6.6 Distance SettingThis page will be refreshed automatically every 5 seconds 4.6.7 Antenna Alignment 4.6.8 Throughput Monitor4.7.1 DHCP Settings 4.7 DHCP4.7.2 DHCP Clients List 4.7.3 Address Reservation To Reserve IP addresses4.8 Wireless settings 4.9 Forwarding 4.9.1 Virtual ServersTo setup a virtual server entry, please take the following steps 4.9.2 Port Triggering 4.9.3 DMZ 4.9.4 UPnP 4.10Security 4.10.1 Firewall4.10.2 IP Address Filtering 4.10.3 Domain Filtering Figure 4-40 Add or Modify a Domain Filtering entry Click the Enabled All button to make all entries enabledFigure 4-39 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions4.10.4 MAC Address Filtering 4.10.5 Advanced Security Figure 4-43 Advanced Security settings 4.11Static Routing To add static routing entries4.12Dynamic DNS 4.12.1 Dyndns.org DDNS4.12.2 Oray.net DDNS 4.12.3 Comexe.cn DDNS 4.13System Tools 4.13.1 Time4.13.2 Firmware 1. Select Using Daylight Saving Time2 The router will reboot after the Upgrading is finished 2 The time will be lost if the router is turned off4.13.3 Factory Defaults 4.13.4 Backup & Restore4.13.5 Ping Watch Dog 4.13.6 Speed Test 4.13.7 Reboot 4.13.8 Password 4.13.9 Syslog4.13.10 Remote Management Bytes 4.13.11 StatisticsStatistics Table ICMPTCP SYN Tx Click the Refresh button to refresh immediatelyChapter 5. Configuring the Device in AP Operation Mode 5.1 Login5.2 Status 5.3 Quick Setup 5.4 Operation Mode5.5 Network 5.6 Wireless 5.6.1 Basic Settings3） The device will reboot automatically after clicking Save 5.6.2 Wireless Mode Page If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP Figure 5-8 Point to Point Bridge Page 5.6.3 Security Settings the wireless network with wireless antenna accessoriesFigure 5-11 Wireless Security 5.6.4 MAC Filtering Figure 5-12 Wireless MAC address Filtering Figure 5-13 Add or Modify Wireless MAC Address Filtering entry6. Click the Save button to save this entry 5.6.5 Wireless Statistics 5.6.6 Distance Setting5.6.7 Antenna Alignment 5.6.8 Throughput Monitor 5.7 DHCP5.7.1 DHCP Settings 5.7.2 DHCP Clients List5.7.3 Address Reservation 5.8 Wireless settings 5.9 System Tools 5.9.1 Firmware5.9.2 Factory Defaults 5.9.3 Backup & Restore5.9.4 Ping Watch Dog 5.9.5 Speed Test2. Wrong process will lead the device unmanaged Figure 5-29 Speed Test 5.9.6 Reboot 5.9.7 PasswordFigure 5-32 System Log 5.9.8 SyslogClick Save when finished Click Clear All to clear all Click Clear ALL to clear all the logsAppendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a Web Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Configure TCP/IP component¾ Setting IP address automatically Now you have two ways to configure the TCP/IP protocol below¾ Setting IP address manually Click OK to keep your settings General Appendix C SpecificationsWireless Physical and EnvironmentAppendix D Glossary