Contents
1910010154
TL-WA5110G 54M High Power Wireless Access Point
All rights reserved
COPYRIGHT & TRADEMARKS
FCC RF Radiation Exposure Statement
FCC STATEMENT
CE Mark Warning
Country
General authorization required for outdoor use
and public service
National Restrictions 2400.0-2483.5 MHz
EN623112008
Product Description 54 M High Power Wireless Access Point
ETSI EN 300 328 V1.7.1
ETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006
CONTENTS
Configuring the Device in AP Operation Mode
5.6.1
Package Contents
Chapter 1. Product Overview
1.2 Features
1.1 Overview of the Product
1.3 Conventions
Indication
Chapter 2. Hardware Installation
2.1. The Front Panel
2.2. The Rear Panel
2.4. Environment Requirements
2.5. Connecting the Device
Ensure the AP is powered on before it restarts completely
2.3. System Requirements
3. Connect the AP to the desktop PC
3.1. Configure the Device
Chapter 3. Quick Installation Guide
For Windows 98 OS or earlier, the PC and AP may need to be restarted
Please check the connection following these steps
3.2. Quick Setup
Figure 3-4 Login Windows
Figure 3-7 Choose WAN Connection Type
Figure 3-9 Quick Setup - Static IP
The IP parameters should have been provided by your ISP
Figure 3-11 Quick Setup - Wireless settings
4.2 Status
4.1 Login
4. Traffic Statistics
IP address and Subnet Mask 2. Wireless
SSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN
1. LAN
4.5.1 LAN
4.3 Quick Setup
4.4 Operation Mode
4.5 Network
4.5.2 WAN
Figure 4-5 WAN - Dynamic IP
You should type the following parameters into the spaces provided
Figure 4-6 WAN - Static IP
Figure 4-7 WAN - PPPoE
4.5.3 MAC Clone
2 If you click Save, the router will prompt you to reboot
4.6 Wireless
4.6.1 Basic Settings
1 Only the PC on your LAN can use the Clone MAC Address To feature
The device will reboot automatically after you click the Save button
4.6.2 Wireless Mode
Figure 4-12 Wireless Mode
Figure 4-13 AP List
Figure 4-14 Wireless Mode settings in AP Router mode
4.6.3 Security Settings
You can select one of the following security options
¾ WEP - Select 802.11 WEP security
Figure 4-15 Wireless Security
2. Shared Key - Select 802.11 Shared Key authentication
3. Open System - Select 802.11 Open System authentication
4.6.4 MAC Filtering
To set up an entry, follow these instructions
Figure 4-16 Wireless MAC address Filtering
¾ Status - The status of this entry either Enabled or Disabled
¾ Description - A simple description of the wireless station
6. Click the Save button to save this entry
4.6.6 Distance Setting
4.6.5 Wireless Statistics
This page will be refreshed automatically every 5 seconds
4.6.8 Throughput Monitor
4.6.7 Antenna Alignment
4.7 DHCP
4.7.1 DHCP Settings
4.7.2 DHCP Clients List
To Reserve IP addresses
4.7.3 Address Reservation
4.8 Wireless settings
4.9.1 Virtual Servers
4.9 Forwarding
To setup a virtual server entry, please take the following steps
4.9.2 Port Triggering
4.9.3 DMZ
4.9.4 UPnP
4.10.1 Firewall
4.10Security
4.10.2 IP Address Filtering
4.10.3 Domain Filtering
To add or modify a Domain Filtering entry, follow these instructions
Click the Enabled All button to make all entries enabled
Figure 4-39 Domain Filtering
Figure 4-40 Add or Modify a Domain Filtering entry
4.10.4 MAC Address Filtering
4.10.5 Advanced Security
Figure 4-43 Advanced Security settings
To add static routing entries
4.11Static Routing
4.12.1 Dyndns.org DDNS
4.12Dynamic DNS
4.12.2 Oray.net DDNS
4.12.3 Comexe.cn DDNS
4.13.1 Time
4.13System Tools
2 The time will be lost if the router is turned off
1. Select Using Daylight Saving Time
2 The router will reboot after the Upgrading is finished
4.13.2 Firmware
4.13.4 Backup & Restore
4.13.3 Factory Defaults
4.13.5 Ping Watch Dog
4.13.6 Speed Test
4.13.7 Reboot
4.13.9 Syslog
4.13.8 Password
4.13.10 Remote Management
ICMP
4.13.11 Statistics
Statistics Table
Bytes
Click the Refresh button to refresh immediately
TCP SYN Tx
5.1 Login
Chapter 5. Configuring the Device in AP Operation Mode
5.2 Status
5.4 Operation Mode
5.3 Quick Setup
5.5 Network
5.6.1 Basic Settings
5.6 Wireless
3） The device will reboot automatically after clicking Save
5.6.2 Wireless Mode
Page
If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP
Figure 5-8 Point to Point Bridge
Page
the wireless network with wireless antenna accessories
5.6.3 Security Settings
Figure 5-11 Wireless Security
5.6.4 MAC Filtering
Figure 5-13 Add or Modify Wireless MAC Address Filtering entry
Figure 5-12 Wireless MAC address Filtering
6. Click the Save button to save this entry
5.6.6 Distance Setting
5.6.5 Wireless Statistics
5.6.7 Antenna Alignment
5.7 DHCP
5.6.8 Throughput Monitor
5.7.2 DHCP Clients List
5.7.1 DHCP Settings
5.7.3 Address Reservation
5.8 Wireless settings
5.9.1 Firmware
5.9 System Tools
5.9.3 Backup & Restore
5.9.2 Factory Defaults
5.9.5 Speed Test
5.9.4 Ping Watch Dog
2. Wrong process will lead the device unmanaged
Figure 5-29 Speed Test
5.9.7 Password
5.9.6 Reboot
Click Clear ALL to clear all the logs
5.9.8 Syslog
Click Save when finished Click Clear All to clear all
Figure 5-32 System Log
Appendix A FAQ
3. I want to use Netmeeting, what do I need to do?
4. I want to build a Web Server on the LAN, what should I do?
5. The wireless stations cannot connect to the router
1. Configure TCP/IP component
Appendix B Configuring the PCs
Now you have two ways to configure the TCP/IP protocol below
¾ Setting IP address automatically
¾ Setting IP address manually
Click OK to keep your settings
Physical and Environment
Appendix C Specifications
Wireless
General
Appendix D Glossary