TP-Link TL-WA5110G manual Factory Defaults, Backup & Restore, Ping Watch Dog

Page 62

4.13.3 Factory Defaults

4.13.3 Factory Defaults

This page (shown in Figure 4-53)allows you to restore the factory default settings for the router.

Figure 4-53 Restore Factory Default

Click the Restore button to reset all configuration settings to their default values.

•The default User Name: admin

•The default Password: admin

•The default IP Address: 192.168.1.1

•The default Subnet Mask: 255.255.255.0

)Note:

All settings you have saved will be lost when the default settings are restored.

4.13.4 Backup & Restore

This page (shown in Figure 4-54)allows you to save current configuration of router as backup or to restore the configuration file you saved before.

Figure 4-54 Backup & Restore Configuration

¾Click the Backup button to save all configuration settings as a backup file to your local computer.

¾To restore the router's configuration, follow these instructions:

•Click the Browse button to select the backup file which you want to restore.

•Click the Restore button.

)Note:

The current configuration will be covered by the uploading configuration file. The restoration process lasts for 20 seconds and the router will restart automatically. Keep the router on during the restoring process, to prevent any damage.

4.13.5 Ping Watch Dog

The Ping Watch Dog is dedicated for continuous monitoring of the particular connection to remote host using the Ping tool. It makes this device continuously ping a user defined IP address ( it can be the internet gateway for example ). If it is unable to ping under the user defined constraints, this device will automatically reboot.

54

Image 62

Contents TL-WA5110G 54M High Power Wireless Access Point 1910010154COPYRIGHT & TRADEMARKS All rights reservedCE Mark Warning FCC STATEMENTFCC RF Radiation Exposure Statement National Restrictions 2400.0-2483.5 MHz General authorization required for outdoor useand public service CountryETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006 Product Description 54 M High Power Wireless Access PointETSI EN 300 328 V1.7.1 EN623112008CONTENTS Configuring the Device in AP Operation Mode 5.6.1 Package Contents 1.1 Overview of the Product 1.2 FeaturesChapter 1. Product Overview 1.3 Conventions 2.2. The Rear Panel Chapter 2. Hardware Installation2.1. The Front Panel Indication2.3. System Requirements 2.5. Connecting the DeviceEnsure the AP is powered on before it restarts completely 2.4. Environment Requirements3. Connect the AP to the desktop PC For Windows 98 OS or earlier, the PC and AP may need to be restarted Chapter 3. Quick Installation Guide3.1. Configure the Device 3.2. Quick Setup Please check the connection following these stepsFigure 3-4 Login Windows Figure 3-7 Choose WAN Connection Type The IP parameters should have been provided by your ISP Figure 3-9 Quick Setup - Static IPFigure 3-11 Quick Setup - Wireless settings 4.1 Login 4.2 Status1. LAN IP address and Subnet Mask 2. WirelessSSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN 4. Traffic Statistics4.5 Network 4.3 Quick Setup4.4 Operation Mode 4.5.1 LAN4.5.2 WAN Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP You should type the following parameters into the spaces providedFigure 4-7 WAN - PPPoE 4.5.3 MAC Clone 1 Only the PC on your LAN can use the Clone MAC Address To feature 4.6 Wireless4.6.1 Basic Settings 2 If you click Save, the router will prompt you to reboot4.6.2 Wireless Mode The device will reboot automatically after you click the Save buttonFigure 4-12 Wireless Mode Figure 4-13 AP List You can select one of the following security options 4.6.3 Security SettingsFigure 4-14 Wireless Mode settings in AP Router mode 3. Open System - Select 802.11 Open System authentication Figure 4-15 Wireless Security2. Shared Key - Select 802.11 Shared Key authentication ¾ WEP - Select 802.11 WEP security4.6.4 MAC Filtering ¾ Description - A simple description of the wireless station Figure 4-16 Wireless MAC address Filtering¾ Status - The status of this entry either Enabled or Disabled To set up an entry, follow these instructions6. Click the Save button to save this entry This page will be refreshed automatically every 5 seconds 4.6.5 Wireless Statistics4.6.6 Distance Setting 4.6.7 Antenna Alignment 4.6.8 Throughput Monitor4.7.1 DHCP Settings 4.7 DHCP4.7.2 DHCP Clients List 4.7.3 Address Reservation To Reserve IP addresses4.8 Wireless settings 4.9 Forwarding 4.9.1 Virtual ServersTo setup a virtual server entry, please take the following steps 4.9.2 Port Triggering 4.9.3 DMZ 4.9.4 UPnP 4.10Security 4.10.1 Firewall4.10.2 IP Address Filtering 4.10.3 Domain Filtering Figure 4-40 Add or Modify a Domain Filtering entry Click the Enabled All button to make all entries enabledFigure 4-39 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions4.10.4 MAC Address Filtering 4.10.5 Advanced Security Figure 4-43 Advanced Security settings 4.11Static Routing To add static routing entries4.12Dynamic DNS 4.12.1 Dyndns.org DDNS4.12.2 Oray.net DDNS 4.12.3 Comexe.cn DDNS 4.13System Tools 4.13.1 Time4.13.2 Firmware 1. Select Using Daylight Saving Time2 The router will reboot after the Upgrading is finished 2 The time will be lost if the router is turned off4.13.5 Ping Watch Dog 4.13.3 Factory Defaults4.13.4 Backup & Restore 4.13.6 Speed Test 4.13.7 Reboot 4.13.8 Password 4.13.9 Syslog4.13.10 Remote Management Bytes 4.13.11 StatisticsStatistics Table ICMPTCP SYN Tx Click the Refresh button to refresh immediately5.2 Status Chapter 5. Configuring the Device in AP Operation Mode5.1 Login 5.5 Network 5.3 Quick Setup5.4 Operation Mode 3） The device will reboot automatically after clicking Save 5.6 Wireless5.6.1 Basic Settings 5.6.2 Wireless Mode Page If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP Figure 5-8 Point to Point Bridge Page 5.6.3 Security Settings the wireless network with wireless antenna accessoriesFigure 5-11 Wireless Security 5.6.4 MAC Filtering Figure 5-12 Wireless MAC address Filtering Figure 5-13 Add or Modify Wireless MAC Address Filtering entry6. Click the Save button to save this entry 5.6.5 Wireless Statistics 5.6.6 Distance Setting5.6.7 Antenna Alignment 5.6.8 Throughput Monitor 5.7 DHCP5.7.1 DHCP Settings 5.7.2 DHCP Clients List5.7.3 Address Reservation 5.8 Wireless settings 5.9 System Tools 5.9.1 Firmware5.9.2 Factory Defaults 5.9.3 Backup & Restore2. Wrong process will lead the device unmanaged 5.9.4 Ping Watch Dog5.9.5 Speed Test Figure 5-29 Speed Test 5.9.6 Reboot 5.9.7 PasswordFigure 5-32 System Log 5.9.8 SyslogClick Save when finished Click Clear All to clear all Click Clear ALL to clear all the logsAppendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a Web Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Configure TCP/IP component¾ Setting IP address automatically Now you have two ways to configure the TCP/IP protocol below¾ Setting IP address manually Click OK to keep your settings General Appendix C SpecificationsWireless Physical and EnvironmentAppendix D Glossary