TP-Link TL-WA5110G manual The wireless stations cannot connect to the router

Page 97

5.The wireless stations cannot connect to the router.

Figure A-8 Virtual Servers

A-9 Add or Modify a Virtual server Entry

5.The wireless stations cannot connect to the router.

1)Make sure the "Wireless Router Radio" is enabled.

2)Make sure that the wireless stations' SSID accord with the router's SSID.

3)Make sure the wireless stations have the right KEY for encryption when the router is encrypted.

4)If the wireless connection is ready, but you can’t access the router, check the IP Address of your wireless stations.

89

Image 97

Contents 1910010154 TL-WA5110G 54M High Power Wireless Access PointAll rights reserved COPYRIGHT & TRADEMARKSFCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning and public service General authorization required for outdoor useNational Restrictions 2400.0-2483.5 MHz CountryETSI EN 300 328 V1.7.1 Product Description 54 M High Power Wireless Access PointETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006 EN623112008CONTENTS Configuring the Device in AP Operation Mode 5.6.1 Package Contents Chapter 1. Product Overview 1.2 Features1.1 Overview of the Product 1.3 Conventions 2.1. The Front Panel Chapter 2. Hardware Installation2.2. The Rear Panel IndicationEnsure the AP is powered on before it restarts completely 2.5. Connecting the Device2.3. System Requirements 2.4. Environment Requirements3. Connect the AP to the desktop PC 3.1. Configure the Device Chapter 3. Quick Installation GuideFor Windows 98 OS or earlier, the PC and AP may need to be restarted Please check the connection following these steps 3.2. Quick SetupFigure 3-4 Login Windows Figure 3-7 Choose WAN Connection Type Figure 3-9 Quick Setup - Static IP The IP parameters should have been provided by your ISPFigure 3-11 Quick Setup - Wireless settings 4.2 Status 4.1 LoginSSID, Channel, Mode, Wireless MAC address, and IP address 3. WAN IP address and Subnet Mask 2. Wireless1. LAN 4. Traffic Statistics4.4 Operation Mode 4.3 Quick Setup4.5 Network 4.5.1 LAN4.5.2 WAN Figure 4-5 WAN - Dynamic IP You should type the following parameters into the spaces provided Figure 4-6 WAN - Static IPFigure 4-7 WAN - PPPoE 4.5.3 MAC Clone 4.6.1 Basic Settings 4.6 Wireless1 Only the PC on your LAN can use the Clone MAC Address To feature 2 If you click Save, the router will prompt you to rebootThe device will reboot automatically after you click the Save button 4.6.2 Wireless ModeFigure 4-12 Wireless Mode Figure 4-13 AP List Figure 4-14 Wireless Mode settings in AP Router mode 4.6.3 Security SettingsYou can select one of the following security options 2. Shared Key - Select 802.11 Shared Key authentication Figure 4-15 Wireless Security3. Open System - Select 802.11 Open System authentication ¾ WEP - Select 802.11 WEP security4.6.4 MAC Filtering ¾ Status - The status of this entry either Enabled or Disabled Figure 4-16 Wireless MAC address Filtering¾ Description - A simple description of the wireless station To set up an entry, follow these instructions6. Click the Save button to save this entry 4.6.6 Distance Setting 4.6.5 Wireless StatisticsThis page will be refreshed automatically every 5 seconds 4.6.8 Throughput Monitor 4.6.7 Antenna Alignment4.7 DHCP 4.7.1 DHCP Settings4.7.2 DHCP Clients List To Reserve IP addresses 4.7.3 Address Reservation4.8 Wireless settings 4.9.1 Virtual Servers 4.9 ForwardingTo setup a virtual server entry, please take the following steps 4.9.2 Port Triggering 4.9.3 DMZ 4.9.4 UPnP 4.10.1 Firewall 4.10Security4.10.2 IP Address Filtering 4.10.3 Domain Filtering Figure 4-39 Domain Filtering Click the Enabled All button to make all entries enabledFigure 4-40 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions4.10.4 MAC Address Filtering 4.10.5 Advanced Security Figure 4-43 Advanced Security settings To add static routing entries 4.11Static Routing4.12.1 Dyndns.org DDNS 4.12Dynamic DNS4.12.2 Oray.net DDNS 4.12.3 Comexe.cn DDNS 4.13.1 Time 4.13System Tools2 The router will reboot after the Upgrading is finished 1. Select Using Daylight Saving Time4.13.2 Firmware 2 The time will be lost if the router is turned off4.13.4 Backup & Restore 4.13.3 Factory Defaults4.13.5 Ping Watch Dog 4.13.6 Speed Test 4.13.7 Reboot 4.13.9 Syslog 4.13.8 Password4.13.10 Remote Management Statistics Table 4.13.11 StatisticsBytes ICMPClick the Refresh button to refresh immediately TCP SYN Tx5.1 Login Chapter 5. Configuring the Device in AP Operation Mode5.2 Status 5.4 Operation Mode 5.3 Quick Setup5.5 Network 5.6.1 Basic Settings 5.6 Wireless3） The device will reboot automatically after clicking Save 5.6.2 Wireless Mode Page If the available AP can’t support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP Figure 5-8 Point to Point Bridge Page the wireless network with wireless antenna accessories 5.6.3 Security SettingsFigure 5-11 Wireless Security 5.6.4 MAC Filtering Figure 5-13 Add or Modify Wireless MAC Address Filtering entry Figure 5-12 Wireless MAC address Filtering6. Click the Save button to save this entry 5.6.6 Distance Setting 5.6.5 Wireless Statistics5.6.7 Antenna Alignment 5.7 DHCP 5.6.8 Throughput Monitor5.7.2 DHCP Clients List 5.7.1 DHCP Settings5.7.3 Address Reservation 5.8 Wireless settings 5.9.1 Firmware 5.9 System Tools5.9.3 Backup & Restore 5.9.2 Factory Defaults5.9.5 Speed Test 5.9.4 Ping Watch Dog2. Wrong process will lead the device unmanaged Figure 5-29 Speed Test 5.9.7 Password 5.9.6 RebootClick Save when finished Click Clear All to clear all 5.9.8 SyslogFigure 5-32 System Log Click Clear ALL to clear all the logsAppendix A FAQ 3. I want to use Netmeeting, what do I need to do? 4. I want to build a Web Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 1. Configure TCP/IP component Appendix B Configuring the PCsNow you have two ways to configure the TCP/IP protocol below ¾ Setting IP address automatically¾ Setting IP address manually Click OK to keep your settings Wireless Appendix C SpecificationsGeneral Physical and EnvironmentAppendix D Glossary