TP-Link 4.1.1 1910011002 manual Panel Layout, Front Panel, Name Status Indication

Page 14

TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide

1.4 Panel Layout

1.4.1 The Front Panel

Figure 1-1 Front Panel sketch

The Router’s LEDs are located on the front panel (View from left to right).

Name

Status

Indication

（Power）

Off

Power is off.

On

Power is on.

 

(System)

Flashing

The Router is working properly.

On/Off

The Router has a system error.

 

(WLAN)

Off

The Wireless function is disabled.

Flashing

The Wireless function is enabled.

 

 

Off

There is no device linked to the corresponding port.

(WAN),

On

There is a device linked to the corresponding port but

(LAN 1-4)

there is no activity.

 

 

Flashing

There is an active device linked to the corresponding port.

 

Slow Flash

A wireless device is connecting to the network by WPS

 

function. This process will last in the first 2 minutes.

 

 

(WPS)

On

A wireless device has been successfully added to the

network by WPS function.

 

 

 

Quick Flash

A wireless device failed to be added to the network by

 

WPS function.

 

 

 

Table 1-1 The LEDs Description

)Note:

After a device is successfully added to the network by WPS function, the WPS LED will keep on for about 5 minutes and then turn off.

- 4 -

Page 13 Page 15
Image 14
Page 13 Page 15
Contents TL-WR841N TL-WR841ND Copyright & Trademarks FCC Statement CE Mark Warning Korea Warning Statements Safety Information Declaration of Conformity Yang Hongliang Product Manager of International BusinessContents 11.1 Backup & Restore Reboot Password System Log Statistics Package Contents Overview of the Router Flexible Access ControlSimple Installation Incredible SpeedMain Features ConventionsName Status Indication Panel LayoutFront Panel Used as Reset button Rear PanelUsed as WPS button System Requirements Installation Environment RequirementsConnecting the Router Hardware Installation Wall-mount Install Quick Installation Guide TCP/IP ConfigurationQuick Installation Guide Please check the connection following these stepsLogin Windows TL-WR841N/TL-WR841ND Quick Setup PPPoE Quick Setup Static IP ISP 12 Quick Setup Wireless PSK Password You can enter Ascii or Hexadecimal characters WirelessLogin StatusQuick Setup WPSUse the Wi-Fi Protected Setup Button II. Enter the client device’s PIN on the Router III. Enter the Router’s PIN on your client deviceNetwork 1 WANWAN Dynamic IP WAN Static IP WAN PPPoE PPPoE Advanced Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide NSW / ACT nsw.bigpond.net.au TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide 12 Pptp Settings MAC Clone 3 LAN 13 MAC Address CloneWireless Wireless Settings16 Wireless Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Wireless Security 18 Wireless Security Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 22 Wireless MAC Filtering To modify or delete an existing entryWireless Advanced TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Wireless Statistics 25 Wireless StatisticsDhcp Settings DhcpDhcp Client List Address ReservationTo Reserve an IP address 29 Address ReservationForwarding Virtual ServersTo set up a virtual server entry 33 Add or Modify a Virtual Server EntryPort Triggering To add a new rule, follow the steps below3 DMZ 35 Add or Modify a Port Triggering EntryUPnP To assign a computer or server to be a DMZ serverSecurity Basic Security39 Basic Security Advanced Security Local Management Remote Management 41 Local ManagementParental Control 42 Remote Management43 Parental Control Settings To add a new entry, please follow the steps below44 Add or Modify Parental Control Entry 11Access Control Rule47 Access Control Rule Management There are two methods to add a new rule Method One48 Quick Setup Create a Host Entry TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Method Two 52 Add Internet Access Control Entry 53 Host Settings HostTarget 54 Add or Modify a Host Entry56 Target Settings 57 Add or Modify an Access Target Entry Schedule To add a new schedule, follow the steps below60 Advanced Schedule Settings Advanced RoutingStatic Routing To add static routing entries, follow the steps belowBandwidth Control System Routing TableControl Settings Rules List14 IP & MAC Binding Setting Binding Settings69 Binding Settings To add IP & MAC Binding entries, follow the steps belowARP List To find an existing entry, follow the steps belowDynamic DNS Comexe.cn DdnsTo set up for DDNS, follow these instructions Dyndns.org Ddns74 Dyndns.org Ddns Settings Time Settings System Tools77 Time settings To set time manuallyTo set Daylight Saving DiagnosticTo set time automatically TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Firmware Upgrade 79 Diagnostic ResultsFactory Defaults Backup & RestoreReboot 82 Backup & Restore ConfigurationPassword System Log86 Mail Account Settings Statistics Statistics Table Current PacketsTCP Appendix a FAQ Figure A-3 MAC Clone Want to use NetMeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Figure A-7 Basic Security Want to build a WEB Server on the LAN, what should I do?Wireless stations cannot connect to the Router Figure A-9 Virtual ServersAppendix B Configuring the PC Configure TCP/IP componentShown in the Figure below ¾ Setting IP address manually Figure B-3Now click OK to keep your settings Environmental and Physical WirelessGeneral Appendix D Glossary 106
Top Page Image Contents