TP-Link 4.1.1 1910011002 manual TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide

Page 47

TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide

¾Mode - Select the desired mode. The default setting is 11bgn mixed.

11b only - Select if all of your wireless clients are 802.11b.

11g only - Select if all of your wireless clients are 802.11g.

11n only- Select only if all of your wireless clients are 802.11n.

11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.

Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can connect to the Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the AP. It is strongly recommended that you set the Mode to 802.11bgn, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the Router.

¾Channel Width - Select the channel width from the drop-down list. The default setting is automatic, which can adjust the channel width for your clients automatically.

) Note:

If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed.

¾Channel - This field determines which operating frequency will be used. The default channel is set to Auto, so the AP will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.

¾Max Tx Rate - You can limit the maximum tx rate of the Router through this field.

¾Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations to access. The wireless radio can only be enabled or disabled by using the WIFI ON/OFF switch on the device.

¾Enable SSID Broadcast - When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. If you select the Enable SSID Broadcast checkbox, the Wireless Router will broadcast its name (SSID) on the air.

¾Enable WDS Bridging - Check this box to enable WDS. With this function, the Router can bridge two or more Wlans. If this checkbox is selected, you will have to set the following parameters as shown in Figure 4-17.Make sure the following settings are correct.

- 37 -

Image 47
Contents TL-WR841N TL-WR841ND Copyright & Trademarks FCC Statement CE Mark Warning Korea Warning Statements Safety Information Yang Hongliang Product Manager of International Business Declaration of ConformityContents 11.1 Backup & Restore Reboot Password System Log Statistics Package Contents Incredible Speed Flexible Access ControlSimple Installation Overview of the RouterConventions Main FeaturesName Status Indication Panel LayoutFront Panel Rear Panel Used as Reset buttonUsed as WPS button System Requirements Installation Environment RequirementsConnecting the Router Hardware Installation Wall-mount Install TCP/IP Configuration Quick Installation GuidePlease check the connection following these steps Quick Installation GuideLogin Windows TL-WR841N/TL-WR841ND Quick Setup PPPoE Quick Setup Static IP ISP 12 Quick Setup Wireless Wireless PSK Password You can enter Ascii or Hexadecimal charactersStatus LoginWPS Quick SetupUse the Wi-Fi Protected Setup Button III. Enter the Router’s PIN on your client device II. Enter the client device’s PIN on the Router1 WAN NetworkWAN Dynamic IP WAN Static IP WAN PPPoE PPPoE Advanced Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide NSW / ACT nsw.bigpond.net.au TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide 12 Pptp Settings MAC Clone 13 MAC Address Clone 3 LANWireless Settings Wireless16 Wireless Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Wireless Security 18 Wireless Security Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering To modify or delete an existing entry 22 Wireless MAC FilteringWireless Advanced TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide 25 Wireless Statistics Wireless StatisticsDhcp Dhcp SettingsAddress Reservation Dhcp Client List29 Address Reservation To Reserve an IP addressVirtual Servers Forwarding33 Add or Modify a Virtual Server Entry To set up a virtual server entryTo add a new rule, follow the steps below Port Triggering35 Add or Modify a Port Triggering Entry 3 DMZTo assign a computer or server to be a DMZ server UPnPBasic Security Security39 Basic Security Advanced Security Local Management 41 Local Management Remote Management42 Remote Management Parental ControlTo add a new entry, please follow the steps below 43 Parental Control Settings44 Add or Modify Parental Control Entry Rule 11Access ControlThere are two methods to add a new rule Method One 47 Access Control Rule Management48 Quick Setup Create a Host Entry TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Method Two 52 Add Internet Access Control Entry Host 53 Host Settings54 Add or Modify a Host Entry Target56 Target Settings 57 Add or Modify an Access Target Entry To add a new schedule, follow the steps below ScheduleAdvanced Routing 60 Advanced Schedule SettingsTo add static routing entries, follow the steps below Static RoutingSystem Routing Table Bandwidth ControlRules List Control SettingsBinding Settings 14 IP & MAC Binding SettingTo add IP & MAC Binding entries, follow the steps below 69 Binding SettingsTo find an existing entry, follow the steps below ARP ListComexe.cn Ddns Dynamic DNSDyndns.org Ddns To set up for DDNS, follow these instructions74 Dyndns.org Ddns Settings System Tools Time SettingsTo set time manually 77 Time settingsTo set Daylight Saving DiagnosticTo set time automatically TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide 79 Diagnostic Results Firmware UpgradeBackup & Restore Factory Defaults82 Backup & Restore Configuration RebootSystem Log Password86 Mail Account Settings Statistics Current Packets Statistics TableTCP Appendix a FAQ Want to use NetMeeting, what do I need to do? Figure A-3 MAC CloneFigure A-5 Add or Modify a Virtual server Entry Want to build a WEB Server on the LAN, what should I do? Figure A-7 Basic SecurityFigure A-9 Virtual Servers Wireless stations cannot connect to the RouterConfigure TCP/IP component Appendix B Configuring the PCShown in the Figure below Figure B-3 ¾ Setting IP address manuallyNow click OK to keep your settings Environmental and Physical WirelessGeneral Appendix D Glossary 106