TP-Link 4.1.1 1910011002 manual Dhcp Settings

Page 56

TL-WR841N/TL-WR841ND

300Mbps Wireless N Router User Guide

4.7 DHCP

Figure 4-26 The DHCP menu

There are three submenus under the DHCP menu (shown in Figure 4-26),DHCP Settings, DHCP Client List and Address Reservation. Click any of them, and you will be able to configure the corresponding function.

4.7.1 DHCP Settings

Choose menu “DHCP → DHCP Settings”, you can configure the DHCP Server on the page as shown in Figure 4-27.The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.

Figure 4-27 DHCP Settings

¾DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

¾Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.

¾End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address.

¾Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the

- 46 -

Image 56

Contents TL-WR841N TL-WR841ND Copyright & Trademarks FCC Statement CE Mark Warning Korea Warning Statements Safety Information Declaration of Conformity Yang Hongliang Product Manager of International BusinessContents 11.1 Backup & Restore Reboot Password System Log Statistics Package Contents Flexible Access Control Simple InstallationOverview of the Router Incredible SpeedMain Features ConventionsName Status Indication Panel LayoutFront Panel Used as Reset button Rear PanelUsed as WPS button System Requirements Installation Environment RequirementsConnecting the Router Hardware Installation Wall-mount Install Quick Installation Guide TCP/IP ConfigurationQuick Installation Guide Please check the connection following these stepsLogin Windows TL-WR841N/TL-WR841ND Quick Setup PPPoE Quick Setup Static IP ISP 12 Quick Setup Wireless PSK Password You can enter Ascii or Hexadecimal characters WirelessLogin StatusQuick Setup WPSUse the Wi-Fi Protected Setup Button II. Enter the client device’s PIN on the Router III. Enter the Router’s PIN on your client deviceNetwork 1 WANWAN Dynamic IP WAN Static IP WAN PPPoE PPPoE Advanced Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide NSW / ACT nsw.bigpond.net.au TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide 12 Pptp Settings MAC Clone 3 LAN 13 MAC Address CloneWireless Wireless Settings16 Wireless Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Wireless Security 18 Wireless Security Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 22 Wireless MAC Filtering To modify or delete an existing entryWireless Advanced TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Wireless Statistics 25 Wireless StatisticsDhcp Settings DhcpDhcp Client List Address ReservationTo Reserve an IP address 29 Address ReservationForwarding Virtual ServersTo set up a virtual server entry 33 Add or Modify a Virtual Server EntryPort Triggering To add a new rule, follow the steps below3 DMZ 35 Add or Modify a Port Triggering EntryUPnP To assign a computer or server to be a DMZ serverSecurity Basic Security39 Basic Security Advanced Security Local Management Remote Management 41 Local ManagementParental Control 42 Remote Management43 Parental Control Settings To add a new entry, please follow the steps below44 Add or Modify Parental Control Entry 11Access Control Rule47 Access Control Rule Management There are two methods to add a new rule Method One48 Quick Setup Create a Host Entry TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Method Two 52 Add Internet Access Control Entry 53 Host Settings HostTarget 54 Add or Modify a Host Entry56 Target Settings 57 Add or Modify an Access Target Entry Schedule To add a new schedule, follow the steps below60 Advanced Schedule Settings Advanced RoutingStatic Routing To add static routing entries, follow the steps belowBandwidth Control System Routing TableControl Settings Rules List14 IP & MAC Binding Setting Binding Settings69 Binding Settings To add IP & MAC Binding entries, follow the steps belowARP List To find an existing entry, follow the steps belowDynamic DNS Comexe.cn DdnsTo set up for DDNS, follow these instructions Dyndns.org Ddns74 Dyndns.org Ddns Settings Time Settings System Tools77 Time settings To set time manuallyTo set Daylight Saving DiagnosticTo set time automatically TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Firmware Upgrade 79 Diagnostic ResultsFactory Defaults Backup & RestoreReboot 82 Backup & Restore ConfigurationPassword System Log86 Mail Account Settings Statistics Statistics Table Current PacketsTCP Appendix a FAQ Figure A-3 MAC Clone Want to use NetMeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Figure A-7 Basic Security Want to build a WEB Server on the LAN, what should I do?Wireless stations cannot connect to the Router Figure A-9 Virtual ServersAppendix B Configuring the PC Configure TCP/IP componentShown in the Figure below ¾ Setting IP address manually Figure B-3Now click OK to keep your settings Environmental and Physical WirelessGeneral Appendix D Glossary 106