TP-Link 4.1.1 1910011002 manual WAN Dynamic IP

Page 34

TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide

Figure 4-6 WAN – Dynamic IP

This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.

¾MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP.

¾Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP.

) Note:

If you find error when you go to a website after entering the DNS addresses, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.

¾Host Name - This option specifies the Host Name of the Router.

¾Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP Address normally, you can choose this option. (It is rarely required.)

- 24 -

Image 34

Contents TL-WR841N TL-WR841ND Copyright & Trademarks FCC Statement CE Mark Warning Korea Warning Statements Safety Information Declaration of Conformity Yang Hongliang Product Manager of International BusinessContents 11.1 Backup & Restore Reboot Password System Log Statistics Package Contents Overview of the Router Flexible Access ControlSimple Installation Incredible SpeedMain Features ConventionsFront Panel Panel LayoutName Status Indication Used as Reset button Rear PanelUsed as WPS button Connecting the Router Installation Environment RequirementsSystem Requirements Hardware Installation Wall-mount Install Quick Installation Guide TCP/IP ConfigurationQuick Installation Guide Please check the connection following these stepsLogin Windows TL-WR841N/TL-WR841ND Quick Setup PPPoE Quick Setup Static IP ISP 12 Quick Setup Wireless PSK Password You can enter Ascii or Hexadecimal characters WirelessLogin StatusQuick Setup WPSUse the Wi-Fi Protected Setup Button II. Enter the client device’s PIN on the Router III. Enter the Router’s PIN on your client deviceNetwork 1 WANWAN Dynamic IP WAN Static IP WAN PPPoE PPPoE Advanced Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide NSW / ACT nsw.bigpond.net.au TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide 12 Pptp Settings MAC Clone 3 LAN 13 MAC Address CloneWireless Wireless Settings16 Wireless Settings TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Wireless Security 18 Wireless Security Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 22 Wireless MAC Filtering To modify or delete an existing entryWireless Advanced TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Wireless Statistics 25 Wireless StatisticsDhcp Settings DhcpDhcp Client List Address ReservationTo Reserve an IP address 29 Address ReservationForwarding Virtual ServersTo set up a virtual server entry 33 Add or Modify a Virtual Server EntryPort Triggering To add a new rule, follow the steps below3 DMZ 35 Add or Modify a Port Triggering EntryUPnP To assign a computer or server to be a DMZ serverSecurity Basic Security39 Basic Security Advanced Security Local Management Remote Management 41 Local ManagementParental Control 42 Remote Management43 Parental Control Settings To add a new entry, please follow the steps below44 Add or Modify Parental Control Entry 11Access Control Rule47 Access Control Rule Management There are two methods to add a new rule Method One48 Quick Setup Create a Host Entry TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Method Two 52 Add Internet Access Control Entry 53 Host Settings HostTarget 54 Add or Modify a Host Entry56 Target Settings 57 Add or Modify an Access Target Entry Schedule To add a new schedule, follow the steps below60 Advanced Schedule Settings Advanced RoutingStatic Routing To add static routing entries, follow the steps belowBandwidth Control System Routing TableControl Settings Rules List14 IP & MAC Binding Setting Binding Settings69 Binding Settings To add IP & MAC Binding entries, follow the steps belowARP List To find an existing entry, follow the steps belowDynamic DNS Comexe.cn DdnsTo set up for DDNS, follow these instructions Dyndns.org Ddns74 Dyndns.org Ddns Settings Time Settings System Tools77 Time settings To set time manuallyTo set time automatically DiagnosticTo set Daylight Saving TL-WR841N/TL-WR841ND300Mbps Wireless N Router User Guide Firmware Upgrade 79 Diagnostic ResultsFactory Defaults Backup & RestoreReboot 82 Backup & Restore ConfigurationPassword System Log86 Mail Account Settings Statistics Statistics Table Current PacketsTCP Appendix a FAQ Figure A-3 MAC Clone Want to use NetMeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Figure A-7 Basic Security Want to build a WEB Server on the LAN, what should I do?Wireless stations cannot connect to the Router Figure A-9 Virtual ServersAppendix B Configuring the PC Configure TCP/IP componentShown in the Figure below ¾ Setting IP address manually Figure B-3Now click OK to keep your settings General WirelessEnvironmental and Physical Appendix D Glossary 106