Kramer Electronics user manual Connecting the VP-23RC Presentation Switcher Section

Page 19

Connecting the VP-23RC Presentation Switcher Section

6Connecting the VP-23RC Presentation Switcher Section

To connect1 the VP-23RCPresentation Switcher section, as illustrated in the example in Figure 5, do the following2:

1.Connect the following video sources:

￿One3 composite video source (for example, a composite video player) to the CV IN 1 BNC connector

￿One3 s-Video source (for example, an s-Video player) to the Y/C IN 1 4-pin connector

￿One3 VGA/UXGA source (for example, a computer graphics source) to the UXGA IN 1 15-pin HD connector

2.Connect the acceptors to a projector4 as follows:

￿The composite video CV OUT BNC connector to the composite video input of the projector

￿The s-Video Y/C OUT 4-pin connector to the s-Video input of the projector

￿The VGA/UXGA UXGA OUT 15-pin HD connector to the VGA/UXGA input of the projector

3.Connect the appropriate balanced5 audio sources and acceptors (not shown in Figure 5).

4.If required, connect the MASTER OUT terminal block connector (not shown in Figure 5; see section 9￿ .4.2).

5.Connect the SPKR OUT block connector to a pair of loudspeakers, by connecting the left loudspeaker to the “L+” and the “L-” terminal block connectors, and the right loudspeaker to the “R+” and the “R-” terminal block connectors. Do not Ground the loudspeakers.

6.Connect the UXGA CAT5 OUT twisted pair connector (see section 6￿ .2) to a line receiver (for example, the TP-120XGA Line Receiver6, which is connected to a remote display).

7.If required, connect a dynamic or a condenser microphone7 to the MIC IN XLR connector.

1 You do not need to connect all the inputs

2 Switch OFF the power on each device before connecting it to your VP-23RC. After connecting your VP-23RC, switch on its power and then switch on the power on each device

3 Although in this example only one source is connected, you can connect all of the four inputs, that is, 12 in total

4 In this example a projector is used, but you can also connect separate outputs such as displays or video recorders 5 To connect audio inputs and outputs, see section 6￿ .1

6 The receiver receives the CAT 5 signal, decodes it and outputs it to a VGA acceptor

7 Use the Con / Dyn switch (refer to the rear panel, item 2 in Figure 3) to select a dynamic microphone or a condenser

15

Image 19
Contents Model Contents Figures Atmel Flip Window TablesGetting Started IntroductionQuick Start Getting Started About the VP-23RC OverviewUnderstanding the Media / Room Controller Section Controlling the VP-23RC VP-23RC Configuration Example Connecting the VP-23RC Rear PanelTerm Definition Recommendations for Achieving the Best PerformanceVP-23RC Front Panel Your Presentation Switcher / ControllerVP-23RC Presentation Switcher / Controller Front View VP-23RC Rear Panel FeatureVP-23RC Presentation Switcher / Controller Rear View RS-232 Feature FunctionVP-23RC Underside Panel Reset VS HSSome models, the front panel may feature built-in rack ears Installing the VP-23RC on a RackBefore Installing on a Rack How to Rack MountConnecting the VP-23RC Presentation Switcher Section If required, connect a PC to the RS-232 port see Connecting the Balanced/Unbalanced Stereo Audio Input/Output CAT 5 Pinout Wiring the CAT 5 Line OUT RJ-45 ConnectorWire Color Shielded Twisted Pair STP / Unshielded Twisted Pair UTPConnecting to the Media / Room Controller Equipment Connecting the VP-23RC Media/Room Controller Section Program Dipswitch Settings Setting the Media / Room Controller Program DipswitchesDescription Controlling the VP-23RC via a PC Controlling the VP-23RCRS-232 Rear Panel Port Location For… Connecting an RS-232 Port to a PCFunction Description Dipswitch SettingsControlling via the Ethernet Control Configuration via RS-232 and RS-485Select Properties Internet Protocol TCP/IP Properties Window Front Panel Buttons Operating Your VP-23RCOperating Your VP-23RC Internet Example of a Typical Setup in the Lecture Auditorium Button Macro Sequence Commands ConfigurationShows an operating example Independent Switchers Mode Presentation Switcher Section OperationMaster Audio Mode Switching in the Master Audio Mode Presentation Switcher Selector Buttons Macro Sequence Flash Memory Upgrade for the Presentation Switcher Section Flash Memory UpgradeUpgrading the Firmware Click OK and select ª Load Hexº from the File menu Loading the Hex Atmel -Flip Window Connected Flash Memory Upgrade for the Media / Room Controller Section KFR-Programmer Window Installing the Web Applet2Troubleshooting Firmware Upgrade Issues Includes the technical specifications1 Technical SpecificationsAudio Gain Control Hex Tables Hex TableDecrease Set the Audio Output Gain Control for the Master AudioIncrease or Decrease the Audio Output Gain by One Step Microphone Master Out Video IncreaseProtocol Definitions Communication ProtocolInstruction Codes Reset Machine Switch Groups0111 1000 1001 +23 Limited Warranty 2900-000155 REV