Kramer Electronics VP-23RC Wiring the CAT 5 Line OUT RJ-45 Connector, CAT 5 Pinout, Wire Color

Page 22

Connecting the VP-23RC Presentation Switcher Section

6.2 Wiring the CAT 5 LINE OUT RJ-45 Connector

Table 5 and Figure 9 define the CAT 5 PINOUT, using a straight pin-to-pin cable with RJ-45 connectors:

Table 5: CAT 5 PINOUT

Figure 9: CAT 5 PINOUT

EIA /TIA 568A

 

 

 

PIN

 

Wire Color

1

Green / White

2

Green

3

Orange / White

4

Blue

5

Blue / White

6

Orange

7

Brown / White

8

Brown

 

 

 

Pair 1

 

4 and 5

Pair 2

 

3 and 6

Pair 3

 

1 and 2

Pair 4

 

7 and 8

 

EIA /TIA 568B

 

 

 

 

PIN

 

 

Wire Color

1

 

Orange / White

2

 

Orange

3

 

Green / White

4

 

Blue

5

 

Blue / White

6

 

Green

7

 

Brown / White

8

 

Brown

 

 

 

 

Pair 1

 

 

4 and 5

Pair 2

 

 

1 and 2

Pair 3

 

 

3 and 6

Pair 4

 

 

7 and 8

6.3Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP)

We recommend that you use shielded twisted pair (STP) cable. There are different levels of STP cable available, and we advise you to use the best quality STP cable that you can afford. Our non-skew-free cable, Kramer BC-STP, which is intended for digital signals and for analog signals where skewing is not an issue, is recommended for the VP-23RC. For cases where there is skewing, our UTP skew-free cable, Kramer BC-XTP, may be used. Bear in mind, though, that we advise using STP cables where possible, since the compliance to electromagnetic interference was tested using those cables.

Although unshielded twisted pair (UTP) cable might be preferred for long range applications, the UTP cable should be installed far away from electric cables, motors and so on, which are prone to create electrical interference. However, since the use of UTP cable might cause inconformity to electromagnetic standards, Kramer does not commit to meeting the standard with UTP cable.

You can connect to a example, the TP-120

remote computer graphics acceptor via a receiver (for ), see section 3￿ .2.

Some Kramer twisted pair products include the Power Connect feature. The VP-23RCdoes not have this feature.

18

KRAMER: SIMPLE CREATIVE TECHNOLOGY

Image 22
Contents Model Contents Figures Tables Atmel Flip WindowGetting Started IntroductionQuick Start Getting Started Overview About the VP-23RCUnderstanding the Media / Room Controller Section Controlling the VP-23RC Connecting the VP-23RC Rear Panel VP-23RC Configuration ExampleRecommendations for Achieving the Best Performance Term DefinitionYour Presentation Switcher / Controller VP-23RC Front PanelVP-23RC Presentation Switcher / Controller Front View Feature VP-23RC Rear PanelVP-23RC Presentation Switcher / Controller Rear View Feature Function RS-232Reset VS HS VP-23RC Underside PanelHow to Rack Mount Installing the VP-23RC on a RackBefore Installing on a Rack Some models, the front panel may feature built-in rack earsConnecting the VP-23RC Presentation Switcher Section If required, connect a PC to the RS-232 port see Connecting the Balanced/Unbalanced Stereo Audio Input/Output Shielded Twisted Pair STP / Unshielded Twisted Pair UTP Wiring the CAT 5 Line OUT RJ-45 ConnectorWire Color CAT 5 PinoutConnecting to the Media / Room Controller Equipment Connecting the VP-23RC Media/Room Controller Section Program Dipswitch Settings Setting the Media / Room Controller Program DipswitchesDescription Controlling the VP-23RC Controlling the VP-23RC via a PCConnecting an RS-232 Port to a PC RS-232 Rear Panel Port Location For…Dipswitch Settings Function DescriptionControl Configuration via RS-232 and RS-485 Controlling via the EthernetSelect Properties Internet Protocol TCP/IP Properties Window Operating Your VP-23RC Front Panel ButtonsOperating Your VP-23RC Internet Example of a Typical Setup in the Lecture Auditorium Commands Configuration Button Macro SequenceShows an operating example Presentation Switcher Section Operation Independent Switchers ModeMaster Audio Mode Switching in the Master Audio Mode Presentation Switcher Selector Buttons Macro Sequence Flash Memory Upgrade Flash Memory Upgrade for the Presentation Switcher SectionUpgrading the Firmware Click OK and select ª Load Hexº from the File menu Loading the Hex Atmel -Flip Window Connected Flash Memory Upgrade for the Media / Room Controller Section Installing the Web Applet2 KFR-Programmer WindowTroubleshooting Firmware Upgrade Issues Technical Specifications Includes the technical specifications1Hex Table Audio Gain Control Hex TablesMicrophone Master Out Video Increase Set the Audio Output Gain Control for the Master AudioIncrease or Decrease the Audio Output Gain by One Step DecreaseCommunication Protocol Protocol DefinitionsReset Machine Switch Groups Instruction Codes0111 1000 1001 +23 Limited Warranty 2900-000155 REV