Kramer Electronics VP-23RC user manual Installing the Web Applet2, KFR-Programmer Window

Page 48

Flash Memory Upgrade

10.2.3Upgrading Firmware

Follow these steps to upgrade the firmware:

1.Double click the KFR-Programmer desktop icon.

The KFR-Programmer window appears (see Figure 31).

Figure 31: The KFR-Programmer Window

2.Select the required COM Port1.

3.Press the File button to select the .s19 firmware file included in the package.

4.Press the Send button to download the file. The Send button lights red.

5.Wait until downloading is completed and the red Send button turns off.

6.Set DIP 1 on the PROGRAM dipswitches located in the CONTROLLER area OFF.

10.2.4Installing the Web Applet2

Follow these steps to install the Web Applet:

1.Connect RC device to your PC through computer networking.

2.Start RC Configuration Software and connect to the RC device (see RC Configuration and Installation Guide).

3.In the Device menu select Upgrade Applet option and browse to MC.dat file included in the package

Wait until uploading is completed and the success message appears. Click OK.

1 To which the VP-23RC is connected on your PC

2 This section is applicable only to firmware version 26.0 and higher and requires RC Configuration Software version 1.26.0.38 and higher

44	KRAMER: SIMPLE CREATIVE TECHNOLOGY

Image 48

Contents Model Contents Figures Tables Atmel Flip WindowIntroduction Getting StartedQuick Start Getting Started Overview About the VP-23RCUnderstanding the Media / Room Controller Section Controlling the VP-23RC Connecting the VP-23RC Rear Panel VP-23RC Configuration ExampleRecommendations for Achieving the Best Performance Term DefinitionYour Presentation Switcher / Controller VP-23RC Front PanelVP-23RC Presentation Switcher / Controller Front View Feature VP-23RC Rear PanelVP-23RC Presentation Switcher / Controller Rear View Feature Function RS-232Reset VS HS VP-23RC Underside PanelInstalling the VP-23RC on a Rack Before Installing on a RackHow to Rack Mount Some models, the front panel may feature built-in rack earsConnecting the VP-23RC Presentation Switcher Section If required, connect a PC to the RS-232 port see Connecting the Balanced/Unbalanced Stereo Audio Input/Output Wiring the CAT 5 Line OUT RJ-45 Connector Wire ColorShielded Twisted Pair STP / Unshielded Twisted Pair UTP CAT 5 PinoutConnecting to the Media / Room Controller Equipment Connecting the VP-23RC Media/Room Controller Section Setting the Media / Room Controller Program Dipswitches Program Dipswitch SettingsDescription Controlling the VP-23RC Controlling the VP-23RC via a PCConnecting an RS-232 Port to a PC RS-232 Rear Panel Port Location For…Dipswitch Settings Function DescriptionControl Configuration via RS-232 and RS-485 Controlling via the EthernetSelect Properties Internet Protocol TCP/IP Properties Window Operating Your VP-23RC Front Panel ButtonsOperating Your VP-23RC Internet Example of a Typical Setup in the Lecture Auditorium Commands Configuration Button Macro SequenceShows an operating example Presentation Switcher Section Operation Independent Switchers ModeMaster Audio Mode Switching in the Master Audio Mode Presentation Switcher Selector Buttons Macro Sequence Flash Memory Upgrade Flash Memory Upgrade for the Presentation Switcher SectionUpgrading the Firmware Click OK and select ª Load Hexº from the File menu Loading the Hex Atmel -Flip Window Connected Flash Memory Upgrade for the Media / Room Controller Section Installing the Web Applet2 KFR-Programmer WindowTroubleshooting Firmware Upgrade Issues Technical Specifications Includes the technical specifications1Hex Table Audio Gain Control Hex TablesSet the Audio Output Gain Control for the Master Audio Increase or Decrease the Audio Output Gain by One StepMicrophone Master Out Video Increase DecreaseCommunication Protocol Protocol DefinitionsReset Machine Switch Groups Instruction Codes0111 1000 1001 +23 Limited Warranty 2900-000155 REV