Kramer Electronics VP-770 user manual Resized image does not go beyond the window boundaries

Page 31

Figure 15: H-Position Slide Bar

4.Press the +/- buttons to move the PiP window horizontally.

Use the V Position menu item in the same way to move the PiP vertically, see Figure 16.

Figure 16: Moving the PiP Window

i

Note that the sequence in which you change the size and position

 

 

of the window is insignificant, as long as you make sure that the

 

resized image does not go beyond the window boundaries.

26

VP-770 - The OSD Menu

 

 

Image 31
Contents VP-770 Page Page Contents Figures Introduction Getting Started Safety InstructionsAchieving the Best Performance Recycling Kramer Products Overview VP-770 Overview VP-770 Overview Hdcp Compliance About the Power Connect FeatureUsing Twisted Pair Cable Defining the VP-770 Presentation Switcher/ScalerHdmi Feature FunctionVP-770 VP-770 Overview Installing in a Rack 15-pin HD Connector Pinout Connecting the VP-770VP-770 Connecting the VP-770 Connecting the VP-770 Presentation Switcher/Scaler Wire Color Wiring the TP Line in / Line OUT RJ-45 ConnectorsAudio Input Pinout Microphone PinoutOutput Master Connection OSD MenuOSD Menu Operation Example Level Range FunctionVP-770 The OSD Menu OSD Control Icons Input Menu Setting FunctionVolatile parameter System Window CustomizationChanging the Size of the Window Changing the Size of the Main and/or PiP WindowIncreasing the Width Moving the Position of the Main and/or PiP WindowSelect Window Customization. The following Window appears Resized image does not go beyond the window boundaries Audio Menu Audio MenuSDI Provide a better quality image and a brighter output Process MenuPicture Menu Picture MenuEnhance Menu Enhance MenuScale Menu Applies to the Single Window display mode onlySelecting the Correct Aspect Ratio SettingMaster Connection Settings Miscellaneous Menu Resolution and firmware versionsFollowing message appears on the display Ignore OSD Coloring Luma Keying Feature Emergency Alert System XML File Transfer EAS Requirements Output ResolutionText Length Definitions Display Modes Single Window Display ModeDual Window Display Mode Activating the Single window ModeRatios of both images are maintained Setting the OSD Menu to PiP Window Control Activating the Dual Window ModeSelecting the PiP Source via the Front Panel Buttons Selecting the PIP SourceSelecting the PiP Source via the OSD Menu Selecting Causes the button to Using the Input Front Panel buttonsControlling the VP-770 Controlling via the Front Panel ButtonsControlling via the OSD Menu Connecting to the VP-770 via your BrowserControlling via the VP-770 Web Pages Connecting the VP-770 via the Ethernet Port Connecting to the VP-770 via RS-232Local Area Connection Properties Window Input Source Ethernet Port Configuration and ControlConnecting the PIP Contact Closure Remote Control PINs Keys Function Controlling via the Infrared Remote Control TransmitterUsing the IR Transmitter Port Tunneling Port TunnelingVP-770 Port Tunneling Flash Memory Upgrade Inputs Technical SpecificationsInput Resolutions Default Communication ParametersPC Input Resolutions Hdmi Input Resolutions DP Input ResolutionsYUV Input Resolutions CV Input ResolutionsTechnical Specifications of the Hdmi Output Signal Output ResolutionsHdmi Output Resolutions PC Output ResolutionsVP-770 RS-232 Communication Protocol Using the Communication ProtocolCommunication Protocol Mimicking OSD Set Command Character Symbols Definitions Meaning Using the Communication Protocol with Legacy ProtocolProtocol Table Mimicking OSD SDI 1st 2nd Level 3rd Level 4th Level RangeRGB LevelLEVEL1 Enhance Sharpness 1st 2nd Level 3rd Level 4th Level Range Func 480p60 1st 2nd Level 3rd Level 4th Level Range Func OFF Keystroke Button Code Protocol 3000 Common Operation CommandsOperation commands Protocol Table Mimicking Remote and Front Panel ButtonsPOWER-MODE #CR Network settings commands Identification commandsProtocol Port Page Safety Warning