Kramer Electronics VP-770 user manual Sdi

Page 33

Setting

Function

Embedded

Set:

Pass-through– to On to pass the digital audio input directly to the output

without any processing or set to Off to process the digital audio input

E

i

Note that this feature is disabled for the non-embedded audio inputs

(PC, CV, YUV).

In case the audio signal is encrypted or compressed set the Pass-

through to On. Note that in some cases there may not be sufficient

capacity to accurately transmit the audio.

Analog Takeover – to On for the analog inputs of the HDMI and DP inputs

to take over the embedded inputs; select Off to use the embedded inputs

E

.

Analog takeover is available only if an unbalanced audio signal is connected

(via the 3.5mm connecter). The embedded audio is disabled as long as the

3.5mm cable is connected to the 3.5mm mini jack

Delay

Set:

Lip Sync delay value [msec]

E

Mic Delay value [msec]

E

Power

Set the power amplifier (SPKR) level to Off or to levels 1 to 4

E

Amplifier

This submenu item is specific for the power amplifier, on top of the general volume

level

SDI

i

Note that SDI is not applicable to the VP-770and appears

Channeling

transparent in the OSD. The commands related to SDI in the

OSD menu are therefore grayed out.

If the transparency of the OSD menu is set to ON this menu item will become invisible (see Section 6.8)

Figure 18: Set the Output Volume Level

28	VP-770 - The OSD Menu

Image 33

Contents VP-770 Page Page Contents Figures Introduction Safety Instructions Getting StartedAchieving the Best Performance Recycling Kramer Products Overview VP-770 Overview VP-770 Overview Using Twisted Pair Cable About the Power Connect FeatureDefining the VP-770 Presentation Switcher/Scaler Hdcp ComplianceHdmi Feature FunctionVP-770 VP-770 Overview Installing in a Rack 15-pin HD Connector Pinout Connecting the VP-770VP-770 Connecting the VP-770 Connecting the VP-770 Presentation Switcher/Scaler Wire Color Wiring the TP Line in / Line OUT RJ-45 ConnectorsAudio Input Pinout Microphone PinoutOSD Menu Operation Example OSD MenuLevel Range Function Output Master ConnectionVP-770 The OSD Menu OSD Control Icons Input Menu Setting FunctionVolatile parameter System Window CustomizationChanging the Size of the Window Changing the Size of the Main and/or PiP WindowIncreasing the Width Moving the Position of the Main and/or PiP WindowSelect Window Customization. The following Window appears Resized image does not go beyond the window boundaries Audio Menu Audio MenuSDI Provide a better quality image and a brighter output Process MenuPicture Menu Picture MenuEnhance Menu Enhance MenuScale Menu Applies to the Single Window display mode onlySelecting the Correct Aspect Ratio SettingMaster Connection Settings Miscellaneous Menu Resolution and firmware versionsFollowing message appears on the display Ignore OSD Coloring Luma Keying Feature Emergency Alert System XML File Transfer Output Resolution EAS RequirementsText Length Definitions Dual Window Display Mode Single Window Display ModeActivating the Single window Mode Display ModesRatios of both images are maintained Setting the OSD Menu to PiP Window Control Activating the Dual Window ModeSelecting the PiP Source via the Front Panel Buttons Selecting the PIP SourceSelecting the PiP Source via the OSD Menu Controlling the VP-770 Using the Input Front Panel buttonsControlling via the Front Panel Buttons Selecting Causes the button toConnecting to the VP-770 via your Browser Controlling via the OSD MenuControlling via the VP-770 Web Pages Connecting the VP-770 via the Ethernet Port Connecting to the VP-770 via RS-232Local Area Connection Properties Window Input Source Ethernet Port Configuration and ControlConnecting the PIP Contact Closure Remote Control PINs Keys Function Controlling via the Infrared Remote Control TransmitterUsing the IR Transmitter Port Tunneling Port TunnelingVP-770 Port Tunneling Flash Memory Upgrade Inputs Technical SpecificationsDefault Communication Parameters Input ResolutionsPC Input Resolutions YUV Input Resolutions DP Input ResolutionsCV Input Resolutions Hdmi Input ResolutionsHdmi Output Resolutions Output ResolutionsPC Output Resolutions Technical Specifications of the Hdmi Output SignalUsing the Communication Protocol VP-770 RS-232 Communication ProtocolCommunication Protocol Mimicking OSD Set Command Using the Communication Protocol with Legacy Protocol Character Symbols Definitions MeaningProtocol Table Mimicking OSD SDI 1st 2nd Level 3rd Level 4th Level RangeRGB LevelLEVEL1 Enhance Sharpness 1st 2nd Level 3rd Level 4th Level Range Func 480p60 1st 2nd Level 3rd Level 4th Level Range Func OFF Operation commands Protocol 3000 Common Operation CommandsProtocol Table Mimicking Remote and Front Panel Buttons Keystroke Button CodePOWER-MODE #CR Network settings commands Identification commandsProtocol Port Page Safety Warning