Lindy Smart Troubleshooting, There are no LED’s illuminated on the Remote Receiver unit, English

Page 8

Troubleshooting

User Manual

English

Troubleshooting

There are no LED’s illuminated on the Remote Receiver unit

Ensure that the AC Adapter is plugged into the mains and the jack is plugged into the socket on the Remote Receiver.

Verify that the connected PC is switched on. Otherwise it may result in display problems.

There is no video signal displayed on the monitor

Check that the VGA cables and CAT5 cable are properly connected to the respective ports on the Receiver and Transmitter units.

Ensure the VGA cables are correctly connected to the computers

Make sure the power adapter is connected to the Receiver

If you still can’t see a picture, try connecting with a short CAT5 patch cable to make sure there is not a fault with the CAT5 cable.

The display is ‘foggy’ or unclear.

Check that the VGA cables are properly connected.

Try adjusting the VGA Tuning control as described in section Installation

Ensure that the VGA resolution is not set too high for the length of Ethernet cable that is used.

Try a higher specification or shorter length CAT5, 5e or 6 cable

Try reducing the display resolution.

6

Image 8

Contents KVM Extender SMART EnglishBenutzerhandbuch DeutschUser Manual Benutzerhandbuch7Manuel Utilisateur Manuale d’usoIntroduction User ManualEnglish Features Package ContentsSystem Requirements Additional Cable RequirementsProduct Information Local Transmitter unitRemote Receiver unit VGA Tuning Control Console Keyboard Mouse PortsInstallation Powering up and checking the installationTransmitter Unit Remote Receiver UnitLocal Transmitter Unit LED Status IndicatorsKeyboard hotkey commands Remote Receiver only Troubleshooting There is no video signal displayed on the monitorThere are no LED’s illuminated on the Remote Receiver unit The display is ‘foggy’ or unclearEinführung BenutzerhandbuchDeutsch Eigenschaften Lieferumfang, PackungsinhaltSystemanforderungen Kabel und ZubehörBenutzerhandbuchDeutsch ProduktinformationLocal Transmitter Unit Remote Receiver UnitTransmitter Local Unit InbetriebnahmeBedeutung der LED Anzeigen Tastatur Hotkey Kommandos nur Remote ReceiverProblemlösung Auf dem Monitor wird kein Bildsignal angezeigtAm Remote Receiver Unit leuchten keine LEDs Das Bild ist unscharf, die Farben sind verwaschenTransmetteur local Manuel UtilisateurFrançais Caractéristiques Contenu de l’emballageSystème Nécessaire Câbles AdditionnelsInformation Produit Transmetteur localRécepteur distant PC/Commutateur KVM Ports de connexion Connection RJ-45 DIP SwitchesRécepteur Alimentation et vérification de l’installationTransmetteur Commandes de raccourci clavier Récepteur distant uniquement Statut des afficheurs LEDRécepteur distant Transmetteur localIl n’y a pas de signal vidéo affiché sur le moniteur Problèmes RencontrésAucune LED n’est allumée sur le Récepteur distant L’affichage est ‘brumeux’ ou n’est pas netIntroduzione Manuale d’usoItaliano Caratteristiche Contenuto della confezioneRequisiti di Sistema Cavi Addizionali RichiestiInformazioni sul Prodotto Unità Locale TrasmittenteUnità Remota Ricevente Porte di connessione Computer/ KVM Switch Porta RJ-45 DIP SwitchesInstallazione Accensione e controllo dell’installazioneUnità trasmittente Unità Remota RiceventeUnità Locale Trasmittente LED Indicatori di statoComandi da Tastiera - Hotkey Solo per unità Remota Risoluzione dei problemi Non ci sono LED accesi sull’Unita RemotaSullo schermo non viene visualizzato alcun segnale L’immagine è “offuscata” o poco visibileRadio Frequency Energy, Certifications CE StatementFCC Statement FCC Warning