Lindy Smart user manual Installation, Transmitter Unit, Remote Receiver Unit, User Manual, English

Page 6

Installation

User Manual

English

Installation

Important: Make sure all of your computers and peripherals are switched OFF before proceeding with the installation.

Transmitter Unit

If the distance between the Local Transmitter and the Remote Receiver is greater than 90 metres (300 feet) you must set DIP switches 1 & 2 on the side of the Transmitter unit to ON.

1.Connect your keyboard, mouse and monitor to the Local Console ports on the Transmitter unit.

2.Using a 3-in-1 KVM cable, connect the ports labelled PC / KVM on the Transmitter unit to the keyboard, mouse and video ports on your computer or the keyboard, video and mouse control console ports on your KVM switch.

3.Connect the CAT5 (or higher) network cable to the RJ-45 port

Remote Receiver Unit

1.Connect your keyboard, mouse and monitor to the ports on the Remote unit.

2.Using the supplied 3-in-1 KVM cable, connect the keyboard, video and mouse ports labelled LOCAL PC to the keyboard, video and mouse ports on your local PC.

3.Connect the CAT5 (or higher) network cable to the RJ-45 port

4.Connect the power supply jack to the port on the Remote unit. Plug the power supply into the mains

Powering up and checking the installation

1.Power on the PC connected to the Remote Receiver unit and then power on the PC / KVM Switch installation connected to the Local Transmitter unit.

2.Check the display quality at the Remote Receiver console. Rotate the VGA Tuning control to adjust the picture quality. If this does not provide a good enough picture quality try changing the dip switches to all possible settings and try VGA tuning again until you get the best result.

4

Image 6

Contents Benutzerhandbuch KVM Extender SMARTEnglish DeutschManuel Utilisateur User ManualBenutzerhandbuch7 Manuale d’usoUser Manual EnglishIntroduction System Requirements FeaturesPackage Contents Additional Cable RequirementsRemote Receiver unit Product InformationLocal Transmitter unit VGA Tuning Control Console Keyboard Mouse PortsTransmitter Unit InstallationPowering up and checking the installation Remote Receiver UnitLED Status Indicators Keyboard hotkey commands Remote Receiver onlyLocal Transmitter Unit There are no LED’s illuminated on the Remote Receiver unit TroubleshootingThere is no video signal displayed on the monitor The display is ‘foggy’ or unclearBenutzerhandbuch DeutschEinführung Systemanforderungen EigenschaftenLieferumfang, Packungsinhalt Kabel und ZubehörLocal Transmitter Unit BenutzerhandbuchDeutschProduktinformation Remote Receiver UnitTransmitter Local Unit InbetriebnahmeBedeutung der LED Anzeigen Tastatur Hotkey Kommandos nur Remote ReceiverAm Remote Receiver Unit leuchten keine LEDs ProblemlösungAuf dem Monitor wird kein Bildsignal angezeigt Das Bild ist unscharf, die Farben sind verwaschenManuel Utilisateur FrançaisTransmetteur local Système Nécessaire CaractéristiquesContenu de l’emballage Câbles AdditionnelsRécepteur distant Information ProduitTransmetteur local PC/Commutateur KVM Ports de connexion Connection RJ-45 DIP SwitchesAlimentation et vérification de l’installation TransmetteurRécepteur Récepteur distant Commandes de raccourci clavier Récepteur distant uniquementStatut des afficheurs LED Transmetteur localAucune LED n’est allumée sur le Récepteur distant Il n’y a pas de signal vidéo affiché sur le moniteurProblèmes Rencontrés L’affichage est ‘brumeux’ ou n’est pas netManuale d’uso ItalianoIntroduzione Requisiti di Sistema CaratteristicheContenuto della confezione Cavi Addizionali RichiestiUnità Remota Ricevente Informazioni sul ProdottoUnità Locale Trasmittente Porte di connessione Computer/ KVM Switch Porta RJ-45 DIP SwitchesUnità trasmittente InstallazioneAccensione e controllo dell’installazione Unità Remota RiceventeLED Indicatori di stato Comandi da Tastiera - Hotkey Solo per unità RemotaUnità Locale Trasmittente Sullo schermo non viene visualizzato alcun segnale Risoluzione dei problemiNon ci sono LED accesi sull’Unita Remota L’immagine è “offuscata” o poco visibileFCC Statement Radio Frequency Energy, CertificationsCE Statement FCC Warning