Dukane 401-8755E-01 user manual Power on/off, Turning on the power, Turning off the power

Page 19
Power off?
POWER (Blinking in orange)
POWER
(Steady orange)
17

Power on/off

Power on/off

WARNING ►When the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

Turning on the power

1. Make sure that the power cord is firmly and correctly connected to the projector and the outlet.

2. Remove the lens cover, and set the power switch to the ON position.

The power indicator will light up in steady orange. Then wait several seconds because the buttons may not function for these several seconds.

STANDBY/ON button

POWER indicator

(1)When AUTO ON in the OPTION menu is set to TURN ON:(40) The lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power switch last time. Afterwards the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in green.

(2)When AUTO ON in the OPTION menu is set to TURN OFF please see step 3.

3.Press the STANDBY/ON button on the projector or the remote control.

To display the picture, select an input signal according to the section "Selecting an input signal" (18).

POWER

(Steady orange)

POWER

(Blinking in green)

POWER

(Steady green)

Turning off the power

Please pay special attention to below two points when you do:

(1) Please do not turn the projector on again for at least 10 minute in this case. Neglect could shorten the lifetime of the lamp.

(2) During use or immediately after use, do not touch around the lamp and vents of the projector (4 ê) It could cause a burn.

1. Press the STANDBY/ON button on the projector or the remote control.

The message "Power off?" will appear on the screen for about 5 seconds.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange.

Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go

off. Attach the lens cover.

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model 8755E Page Thank you for purchasing this projector About this manualTrademark acknowledgment Content Preparations Projector featuresFastening the lens cover Projector Part namesVideo ports  Power switch AC inlet  RGB OUT port Control buttons Remote controlSetting up Min Max Down ArrangementElevator feet Elevator button Adjusting the projectors elevatorHow to attach Using the Security BarSecurity Bar Anti-theft chain or wire sold separately About Plug-and-Play capability Connecting your devicesRS-232C USB Connecting to a monitor outputConnecting to a speaker with amplifier output Examples of connection with a computerCB/PB Examples of connection with a VCR/DVD playerCR/PR AC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlOff. Attach the lens cover Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom and focus Selecting an input signal For a component video signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenMove pointer Available function Remote control operationOperating the computer screen USB mouse and keyboard controlEasy Menu Multifunctional settingsUsing the menu function Menu button Enter button Cursor buttons Reset buttonEasy Menu Easy Menu Picture Menu Adjust the level using the buttonsGamma Color Temp Picture MenuMY Memory Position PhaseImage Menu Over ScanImage Menu For a video signal or s-video signalAuto Adjust For a component video signalColor Space Input MenuProgressive Video NRFrame Lock Input MenuComponent Video FormatCustom Resolution Setup Menu Audio Setup MenuUsing the buttons / switches the mode for mirror status VolumeMenu Position Screen MenuBlank Start UP Screen MenuMyScreen Lock Message Auto Search Option MenuAuto on MY Button Option MenuAuto OFF Lamp TimeFilter Message ServiceFAN Speed GhostInformation Factory ResetRemote Freq Use the / button to change the Projectors remote sensorSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Lamp MaintenanceLamp cover Screw Screws Handle Case of replacement by yourselfLamp Type number = 456-8755EType number = NJ22222 Air filterHandle Filter cover Air filter’s knob Air filterPage Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecifications Warranty and after-serviceSpecifications Technical Example of computer signalInitial set signals 75Ω terminated positive Connection to the ports±0.1Vp-p, 75Ω terminator Component Video D Y, E CB/PB, F CR/PR200mVrmsmax kΩ output impedance 200mVrmsmax kΩ terminationProtocol Connecting the cableCommunications setting Command dataIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandRS-3C Communication CRC Be EF EA F5 Be EF CE D6 CB D6 Pуcckий Be EF 08 D3 RGB1 Page Page Audio Visual Products
Top Page Image Contents