Dukane 401-8755E-01 user manual Option Menu, Auto Search, Auto on

Page 42

OPTION Menu

OPTION Menu

With the OPTION menu, the items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table.

72

#761 1((

OKP

%4''0

.#/2 +/'

 

126+1

(+.

J

'#5;/'07

/;$76 10

 

48+%'

 

 

5'%74+6'4;6+/'

 

Item

Description

 

Using the buttons ▲/▼ turns on/off the automatic signal search function.

 

TURN ON TURN OFF

 

When the TURN ON is selected, detecting no signal automatically cycles

AUTO SEARCH

through input ports in the following order. The search is started from the

current port. Then when an input is found, the projector will stop searching

 

 

and display the image.

 

RGB IN1 RGB IN2 COMPONENT VIDEO S-VIDEO VIDEO

 

 

 

Using the buttons ▲/▼ turns on/off the automatic keystone function.

 

TURN ON TURN OFF

 

TURN ON : Automatic keystone distortion correction will be

AUTO

executed whenever changing the slant of the projector.

TURN OFF : This function is disabled. Please execute the AUTO

KEYSTONE

KEYSTONE EXECUTE in the SETUP Menu for automatic keystone

 

distortion correction.

 

When the projector is suspended from the ceiling this feature will

 

not function properly so select TURN OFF.

 

This function will be unavailable when Transition Detector is on (48).

 

Using the buttons ▲/▼ turns on/off the AUTO ON function.

 

TURN ON TURN OFF

 

When set to TURN ON, the lamp will only be automatically turned on when

 

the Power switch is turned on after the power was turned off by Power

 

switch last time.

 

The lamp will not be automatically turned on when the Power switch is

 

turned on if the lamp was turned off with the following procedures.

 

• The lamp was turned off with a remote control, projector button, or

 

power turn off command.

AUTO ON

• The lamp was turned off with an AUTO OFF function (41).

 

• The lamp was turned on by an AUTO ON function and was turned

 

off about 30 minutes after no signal had been detected.

 

When no input is detected after the power on and AUTO OFF time is set to 0,

 

the projector will be turned off after about 30 minutes passed.

 

When no input is detected after the power on and AUTO OFF time is set to

 

1 to 99, the projector will be turned off after the passed time reaches at the

 

set time.

 

If one of the projector's buttons or the remote control buttons is pressed

 

or one of the commands (except get commands) is transmitted from the

 

control port during the corresponding time, projector will not be turned off.

40

Image 42
Contents Model 8755E Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Projector features PreparationsFastening the lens cover Part names ProjectorRGB OUT port  Power switch AC inlet  Video ports Remote control Control buttonsSetting up Arrangement Min Max DownAdjusting the projectors elevator Elevator feet Elevator buttonUsing the Security Bar How to attachSecurity Bar Anti-theft chain or wire sold separately Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output RS-232C USBExamples of connection with a VCR/DVD player CB/PBCR/PR Connecting power supply AC inlet Connector Power cordRemote control Putting batteriesUsing the remote control Changing the signal setting for the projectors remote sensorTurning off the power Power on/offTurning on the power Off. Attach the lens coverOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSelecting an input signal Searching an input signalAdjusting the zoom and focus Selecting an aspect ratio For a video signal or s-video signal Using the automatic adjustment featureAdjusting the position  For a component video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Move pointerMenu button Enter button Cursor buttons Reset button Multifunctional settingsUsing the menu function Easy MenuEasy Menu Easy Menu Adjust the level using the buttons Picture MenuGamma Picture Menu Color TempMY Memory Over Scan PhaseImage Menu PositionFor a component video signal For a video signal or s-video signalAuto Adjust Image MenuVideo NR Input MenuProgressive Color SpaceVideo Format Input MenuComponent Frame LockCustom Resolution Setup Menu Volume Setup MenuUsing the buttons / switches the mode for mirror status AudioScreen Menu Menu PositionBlank Screen Menu Start UPMyScreen Lock Message Option Menu Auto SearchAuto on Lamp Time Option MenuAuto OFF MY ButtonGhost ServiceFAN Speed Filter MessageUse the / button to change the Projectors remote sensor Factory ResetRemote Freq InformationChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code Turning Off the PIN Lock Function If you have forgotten your PIN CodeUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off Maintenance LampType number = 456-8755E Case of replacement by yourselfLamp Lamp cover Screw Screws HandleAir filter Type number = NJ22222Handle Filter cover Air filter Air filter’s knobPage Internal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workColor settings are not correctly adjusted Volume is adjusted to an extremely low levelAudio setting is not correct Color Space setting is not suitableWhisper function is working Not properly adjustedEither the focus and/or horizontal phase settings are Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationsSpecifications Example of computer signal TechnicalInitial set signals Connection to the ports 75Ω terminated positiveComponent Video D Y, E CB/PB, F CR/PR ±0.1Vp-p, 75Ω terminator200mVrmsmax kΩ termination 200mVrmsmax kΩ output impedanceCommand data Connecting the cableCommunications setting ProtocolUsing the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandRS-3C Communication CRC Be EF EA F5 Be EF CE D6 CB D6 Pуcckий Be EF 08 D3 RGB1 Page Page Audio Visual Products