Canon 7365 user manual ❹ Correcting Keystone Distortion, Adjusting with buttons on the cabinet

Page 38

3. Projecting an Image (Basic Operation)

Correcting Keystone Distortion

Correcting Keystone Distortion

If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following steps to correct keystone distortion

NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.

NOTE: The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.

NOTE: Turning off the projector will cause your manual keystone adjustments to return to "0". To save your manual keystone ad- justments, select [Keystone save] from the menu. See page 48.

Adjusting with buttons on the cabinet

1.Press the SELECT or button with no menus displayed The keystone bar will be displayed.

2.Use the SELECT or to correct the keystone distortion. The keystone bar will be closed after a period of time.

NOTE: When the menu is displayed, the above operation is not available. When the menu is displayed, press the MENU button to close the menu and start the Keystone correction.

From the menu, select [Setup] [General] [Keystone adjustment]. The changes can be saved with [Keystone save]. (page 48)

Adjusting with the Remote Control

1.Press the MENU button. The menu will be displayed.

2.Press the SELECT button to select [Setup] and press the OK or SELECT button.

3.Press the SELECT button to select [Keystone adjustment] from the [General] tab.

4.Press the SELECT or button. Adjust so that the image is rectangular.

5.Press the MENU button. The menu will be closed.

TIP: The changes can be saved with [Keystone save]. (page 48)

29

Image 38
Contents LV-7365/LV-7265/LV-7260/LV-X7 Important Information Safety CautionsPrecautions Machine Noise Information Regulation 3. GpsgvCanadian Radio Interference Regulations Réglementation canadienne sur les intérferences radioLamp Replacement Important InformationFire and Shock Precautions Important SafeguardsInstallation Do Not Use in the Following EnvironmentsImportant Information About High altitude mode Use Caution When Carrying or Transporting the ProjectorRemote Control Precautions LV-7365Table of Contents Viii For LV-7365/LV-7265/LV-7260 Introduction❶ Whats in the Box? Introduction Features youll enjoy❷ Introduction to the Projector Congratulations on Your Purchase of The ProjectorIntroduction Rear ❸ Part Names of the ProjectorFront/Top Push one end of the logo gently Introduction BottomTo turn the logo upside down, follow the steps below Release your hold and turn the logo upside downSelecting from Input List Introduction Top FeaturesDetecting the Signal Automatically Introduction Terminal Panel Features 7 8 ❹ Part Names of the Remote Control Freeze Button / Button17. D. Zoom + Button Click ButtonHorizontal range Vertical range Introduction Battery InstallationOperating Range for Wireless Remote Control Installation and Connections Selecting a Location LV-7365/LV-7265 ❶ Setting Up the Screen and the ProjectorInstallation and Connections Throw Distance and Screen Size300 Reflecting the Image ❷ Making Connections Digital Audio Analog IN-2 Analog IN-1Digital Analog IN-1 Analog IN-2 When Viewing a DVI Digital Signal LV-7365/LV-7265 Audio cable not supplied Installation and Connections Connecting an External Monitor AudioUse audio equipment for stereo sound Video Audio LV-7365 / LV-7265 Audi OIN Projecting an Image Basic Operation ❶ Turning on the ProjectorPress the OK button to execute the selection Projecting an Image Basic OperationTo select a menu language, follow these steps ❷ Selecting a Source Detecting the Signal AutomaticallySelecting Default Source Rear foot height can be adjusted up to 10 mm/0.4 inch ❸ Adjusting the Picture Size and PositionAdjust the Tilt Foot Lift the front edge of the projectorProjecting an Image Basic Operation Zoom Focus❹ Correcting Keystone Distortion Adjusting with buttons on the cabinetAdjusting with the Remote Control Correcting Keystone DistortionAuto keystone will be highlighted ❺ Automatically Optimizing on RGB Image ❻ Turning Up or Down VolumeAdjusting the Image Using Auto PC adjustment ❼ Turning off the Projector To turn off the projector❽ After Use Preparation Make sure that the projector is turned off❷ Freezing a Picture Convenient Features❶ Turning off the Image and Sound ❸ Enlarging and Moving a PictureConnecting the remote mouse receiver to your computer ❹ Using the Remote Mouse Receiver LV-7365/LV-7265/LV-7260Convenient Features When operating a computer via the remote mouse receiverAbout Drag Mode To enable the Password function ❺ Preventing the Unauthorized Use of the ProjectorPress the Menu button To turn on the projector when Password is enabledTo disable the Password function Type in your password and press the OK button Using On-Screen Menu ❶ Using the MenusFor Selecting items Solid triangle Using On-Screen MenuFor Adjusting items Slide bar For Selecting items Radio button❷ Menu Elements TabImage adjustment ❸ List of Menu ItemsReset Detail settings Selecting Reference Setting Reference ❹ Menu Descriptions & Functions Image adjustmentImage mode Selecting Gamma Correction Mode GammaReset ❺ Menu Descriptions & Functions Display settingsAdjusting White Balance White balance Selecting Aspect Ratio AspectCopyright General ❻ Menu Descriptions & Functions SetupSelecting Wall Color Correction Mode Screen color Enabling Auto Keystone Auto keystone LV-7365/LV-7265Selecting Menu Language Language Selecting Lamp Mode Lamp modeEnabling Key Sound and Error Sound Beep Selecting Communication Speed Communication speed Using On-Screen Menu InstallationSelecting Projector Orientation Image flip H/V Disabling the Cabinet Buttons Key lockOptions Enabling Fan Speed Mode Fan mode Enabling Direct Power on Direct power onEnabling Power Management Power management Selecting Default Source Default source selectEnabling the deinterlace Deinterlace Input signal selectSelecting Signal Format ❼ Menu Descriptions & Functions Information Input signalModel Lamp lifeH Replacement lamp Normal Quiet Usage timeResetting settings and adjustments Reset ❽ Menu Descriptions & Functions ResetUsing On-Screen Menu Version Clearing Lamp Hour Meter Lamp counterLV-7365 Maintenance❶ Cleaning or Replacing the Filter LV-7265/LV-7260/LV-X7❷ Cleaning the Cabinet and the Lens Maintenance❸ Replacing the Lamp To replace the lampRemove the lamp cover Remove the lampInsert a new lamp until the lamp is plugged into the socket If a temperature error occurs ❶ TroubleshootingIndicator Messages AppendixProblem Check These Items AppendixAppendix Electrical ❷ SpecificationsOptical LV-X7 1500 lmMechanical ❸ Cabinet Dimensions LV-7260/LV-X7❹ Pin Assignments of D-Sub Analog Input Connector Mini D-Sub 15 Pin Connector❺ Compatible Input Signal List ❻ Relationship between Screen Size and Projection distance 102 122 78 cm 13 cm 142 107 92 cm 15 cm PC Control Codes Service Port Mini DIN-8P❼ PC Control Codes and Cable Connection Cable ConnectionVideo and Audio ❽ Troubleshooting Check ListPower OtherComputer Installation environmentSignal cable Video equipmentCanon U. S. A., INC