Canon 7365 user manual Auto keystone will be highlighted

Page 39

3. Projecting an Image (Basic Operation)

Adjusting with the Auto Keystone Function (LV-7365/LV-7265)

The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special operation required. Just put the projector on a flat surface.

TIP: Even when the menu setting for [Auto keystone] is turned on, [Keystone adjustment] can be adjusted manually.

To turn on [Auto keystone], proceed the following steps.

1.Press the MENU button The menu will be displayed.

2.Press the SELECT button to select [Setup] and press the OK button. The [General] tab will be highlighted.

3.Press the SELECT button.

The [Auto keystone] will be highlighted.

4.Press the SELECT or button to select [On].

5.Press the MENU button. The menu will be closed.

NOTE:

Vertical distortions between offset angles of +/- 30 degrees can be corrected.

The Auto Keystone correction will take effect in 2 seconds after changing the projection angle during projection.

The left and right (horizontal) keystone correction is not available.

Place the projector so that the lens surface is parallel to the screen.

The rear feet of the projector can be adjusted to level the projector.

NOTE:

Auto and Manual Keystone correction angle could be less than 30 degrees depending on the signal and/or aspect ratios.

Using keystone correction can cause the image to be slightly blurred because the correction is made electronically.

NOTE:

When the menu is displayed, the Keystone Correction operation is not available by using the buttons on the projector cabinet. When the menu is displayed, press the BACK button to close the menu and then perform the Keystone correction.

From the menu, select [Setup] [General] [Keystone adjustment]. The changes can be saved with [Keystone save]. (page 48)

NOTE: If you have one of the following conditions, the projector's Auto

Keystone may not be performed correctly.

-the screen is tilted

-the room temperature is too high or too low

-the optical zoom is maximized or minimized

30

Image 39
Contents LV-7365/LV-7265/LV-7260/LV-X7 Machine Noise Information Regulation 3. Gpsgv Safety CautionsPrecautions Important InformationRéglementation canadienne sur les intérferences radio Canadian Radio Interference RegulationsImportant Information Lamp ReplacementDo Not Use in the Following Environments Important SafeguardsInstallation Fire and Shock PrecautionsImportant Information LV-7365 Use Caution When Carrying or Transporting the ProjectorRemote Control Precautions About High altitude modeTable of Contents Viii Introduction ❶ Whats in the Box?For LV-7365/LV-7265/LV-7260 Congratulations on Your Purchase of The Projector Features youll enjoy❷ Introduction to the Projector IntroductionIntroduction ❸ Part Names of the Projector Front/TopRear Release your hold and turn the logo upside down Introduction BottomTo turn the logo upside down, follow the steps below Push one end of the logo gentlyIntroduction Top Features Detecting the Signal AutomaticallySelecting from Input List Introduction Terminal Panel Features 7 8 ❹ Part Names of the Remote Control Click Button / Button17. D. Zoom + Button Freeze ButtonIntroduction Battery Installation Operating Range for Wireless Remote ControlHorizontal range Vertical range Installation and Connections Throw Distance and Screen Size ❶ Setting Up the Screen and the ProjectorInstallation and Connections Selecting a Location LV-7365/LV-7265300 Reflecting the Image Digital Audio Analog IN-2 Analog IN-1 ❷ Making ConnectionsDigital Analog IN-1 Analog IN-2 When Viewing a DVI Digital Signal LV-7365/LV-7265 Audio cable not supplied Audio Installation and Connections Connecting an External MonitorUse audio equipment for stereo sound Video Audio LV-7365 / LV-7265 Audi OIN ❶ Turning on the Projector Projecting an Image Basic OperationProjecting an Image Basic Operation To select a menu language, follow these stepsPress the OK button to execute the selection Detecting the Signal Automatically Selecting Default Source❷ Selecting a Source Lift the front edge of the projector ❸ Adjusting the Picture Size and PositionAdjust the Tilt Foot Rear foot height can be adjusted up to 10 mm/0.4 inchFocus Projecting an Image Basic Operation ZoomCorrecting Keystone Distortion Adjusting with buttons on the cabinetAdjusting with the Remote Control ❹ Correcting Keystone DistortionAuto keystone will be highlighted ❻ Turning Up or Down Volume Adjusting the Image Using Auto PC adjustment❺ Automatically Optimizing on RGB Image To turn off the projector ❼ Turning off the ProjectorPreparation Make sure that the projector is turned off ❽ After Use❸ Enlarging and Moving a Picture Convenient Features❶ Turning off the Image and Sound ❷ Freezing a PictureWhen operating a computer via the remote mouse receiver ❹ Using the Remote Mouse Receiver LV-7365/LV-7265/LV-7260Convenient Features Connecting the remote mouse receiver to your computerAbout Drag Mode ❺ Preventing the Unauthorized Use of the Projector To enable the Password functionTo turn on the projector when Password is enabled To disable the Password functionPress the Menu button Type in your password and press the OK button ❶ Using the Menus Using On-Screen MenuFor Selecting items Radio button Using On-Screen MenuFor Adjusting items Slide bar For Selecting items Solid triangleTab ❷ Menu Elements❸ List of Menu Items Image adjustmentReset Selecting Gamma Correction Mode Gamma ❹ Menu Descriptions & Functions Image adjustmentImage mode Detail settings Selecting Reference Setting ReferenceSelecting Aspect Ratio Aspect ❺ Menu Descriptions & Functions Display settingsAdjusting White Balance White balance ResetCopyright Enabling Auto Keystone Auto keystone LV-7365/LV-7265 ❻ Menu Descriptions & Functions SetupSelecting Wall Color Correction Mode Screen color GeneralSelecting Lamp Mode Lamp mode Enabling Key Sound and Error Sound BeepSelecting Menu Language Language Disabling the Cabinet Buttons Key lock Using On-Screen Menu InstallationSelecting Projector Orientation Image flip H/V Selecting Communication Speed Communication speedOptions Selecting Default Source Default source select Enabling Direct Power on Direct power onEnabling Power Management Power management Enabling Fan Speed Mode Fan modeInput signal select Selecting Signal FormatEnabling the deinterlace Deinterlace Usage time Input signalModel Lamp lifeH Replacement lamp Normal Quiet ❼ Menu Descriptions & Functions InformationClearing Lamp Hour Meter Lamp counter ❽ Menu Descriptions & Functions ResetUsing On-Screen Menu Version Resetting settings and adjustments ResetLV-7265/LV-7260/LV-X7 Maintenance❶ Cleaning or Replacing the Filter LV-7365Maintenance ❷ Cleaning the Cabinet and the LensTo replace the lamp ❸ Replacing the LampRemove the lamp Remove the lamp coverInsert a new lamp until the lamp is plugged into the socket Appendix ❶ TroubleshootingIndicator Messages If a temperature error occursAppendix Problem Check These ItemsAppendix LV-X7 1500 lm ❷ SpecificationsOptical ElectricalMechanical LV-7260/LV-X7 ❸ Cabinet DimensionsMini D-Sub 15 Pin Connector ❹ Pin Assignments of D-Sub Analog Input Connector❺ Compatible Input Signal List ❻ Relationship between Screen Size and Projection distance 102 122 78 cm 13 cm 142 107 92 cm 15 cm Cable Connection Service Port Mini DIN-8P❼ PC Control Codes and Cable Connection PC Control CodesOther ❽ Troubleshooting Check ListPower Video and AudioVideo equipment Installation environmentSignal cable ComputerCanon U. S. A., INC