Canon WUX10 manual Freeze parameterID Image now frozen, Image now not frozen, Freezes image

Page 36

Projector WUX10 MarkII User Commands

FREEZE

Freeze status

Format

FREEZE=<FREEZE parameter:ID>

GET□FREEZE / ?△FREEZE

<FREEZE parameter:ID>

ON	Image now frozen
OFF	Image now not frozen

Environment

	Power					Input
OFF	ON	PM	D-RGB	A-RGB1	A-RGB2	COMP	VIDEO	HDMI	None
X	O	X	-

Response

"i:OK" is returned if the parameter was set properly.

For 'GET FREEZE' or '?FREEZE', current freeze status is returned as

'gFREEZE=ON'

'g:FREEZE=OFF'

For details on other responses, refer to the "Error List".

Description

(1)This command is used to freeze the image.

(2)This command is identical to pressing the “FREEZE” button on the remote control.

(3)The current freeze status can be obtained using the GET command. ("GET FREEZE")

Example

Setting

>	FREEZE=ON	Freezes image.
<	i:OK

Reference

>GET FREEZE or ?FREEZE The current freeze status is referenced.

< g:FREEZE=ON

*Commands are indicated by ">", and responses are indicated by "<".

Revision History / Date

Changes

Revised by

Approved by

- 32 -

Image 36

Contents Projector WUX10 MarkII User Commands Revision History Table of Contents Error List Error Processing Other Appendix 1. Reset Items Overview Same as orCommunication Specifications Projector can be controlled via serial or LAN connectionCommunication System Serial Request transmissions sent from PC to the projector Delimiters Delimiters for commands sent from PC ERR response An error message is outputExample ExampleOr more Ascii characters 20h to 7Fh Character string Or more Ascii characters 20h to 7FhCommunication Flow Transmission sentCommand System AutopcPower Auto SET Autosetexe Aspect Input Auto PC Autopc Command List PMM Details of Command This indicates the command formatThis describes the command response This includes the command function, conditions, and notesFor details on other responses, refer to the Error List 6AXADJControl Setting 6AXR-YIOK is returned if the parameter was set properly R hue is set to -8, and the color saturation is set toAuto focusing is executed during auto setup execution AscomboAuto set combination parameterID Combine Do not combineAspect Setting This sets the screen size to Wide ASPECT=169GASPECT=TRUE Autopc Autopc iOKAuto focusing is executed AutosetexeSetting This sets the volume toThis retrieves the volume AvolBlank Blank parameterIDBlank is set to on ReferenceScreen when Blank setting parameterID Set to Black screen when screen is BlankBlankcolor Black screenSetting values for Brightness settingNumber are -20 to Setting This sets the brightness toBRI Reference This retrieves the brightnessBeep sound settingNumber Beep sound mute Beep sound output BVOL=Beep sound settingNumberBvol This mutes the Beep soundReturns the user command version as GCOMVER=User command versionCharacter stringComver Setting values for Contrast settingNumber are -20 to Setting This sets the contrast to +3Cont Reference This retrieves the contrastDgamma This sets the dynamic gamma function to WeakDots DOTS=Number of dotsNumberDOTS=1650 GDOTS=1200This sets direct power-on to OFF Direct power-on is set to onDpon ERR Fcontdrv Freeze Freeze parameterID Image now frozenImage now not frozen Freezes imageFstepdrv Focus lens step control parameterIDFSTEPDRV=Focus lens step control parameterID Ftoneadj Setting values for Gamma adjustment Number are -10 to GAMMA=Gamma adjustmentNumberGamma This sets the gamma correction toGuide setting parameter ID Guide display on GuideGuide display OFF Guide display is set to onHPIX/VPIX HPIX=1024GVPIX= HPOS/VPOS Reference This acquires the vertical positionSetting values for Hue setting valueNumber are -20 to Setting This sets the hue to +8HUE Reference This retrieves the hueImage GIMAGE=CINEMA Imageflip Input Input selection parametersIDComponent VideoSetting This locks the remote control keys KeylockReference This retrieves the key lock state Lamp output setting parametersID LampNormal Silent coolingFor all other responses, refer to Error List LampcounterReturns current lamp on time as GLAMPCOUNTER=Lamp on timeCharacter stringLang Setting LED display is set to on LedilluminateThis sets the LED display to OFF Lmpt None Reference This retrieves the lamp timeHours 34 minutes Main Mode switch Mode referenceMode GMODE=REMOTE GMODE=LOCALThis returns the audio/beep sound to its original setting This mutes the volumeReference GET Mute or ?MUTE This retrieves the volume state MuteParameters for setting display screen in no-signal modeID This sets the Blue screen when no signals are inputNosig GNOSIG=BLUEParameters for setting display screen at startupID PjonCanon logo No displayPower management setting parametersID Exit modeReference This retrieves the power management mode PMMPower ParameterID Power onPower OFF POWERParameterIDProdcode Product name is returned asGPRODCODE=Product nameCharacter string Progressive conversion setting parametersID This sets the progressive conversion setting to OFFProg Remote control emulation button parametersID POWEROFF, Power button pressed twiceUP+REP, Button press start DOWN+REP, Button press startRC Power iOK Remote control setting parametersID Remote control channel This sets the remote control channel to ch1Rcch Reset Reset parametersIDLamp on time reset Current image adjustment resetControl This resets the lamp on time Reset LamptimeSetting values for R/G/B gain settingNumber are -60 to Setting R gain is set to 10, G gain to 11 and B gain toRgbgain RGB gain values are obtainedSetting values for R/G/B offset settingNumber are -60 to RgboffsetRGB offset values are obtained Or ?RGBOFFSETRomver ROM version of the firmware is returned asGROMVER=ROM versionCharacter string SAT Reference This retrieves the color saturationSAT=-10 GET SAT or ?SATSetting This sets the screen aspect to Scrnaspect1610 Display Reference This retrieves the screen aspectInput signal selection parameterID AUTOAuto SEL=Input signal selection parameterIDGSEL=Detected input signalID SELSetting This sets the input signal selection to Auto Reference This retrieves the input signalGET SEL or ?SEL GSEL=575pSetting values for Sharpness settingNumber are -10 to SHARP=Sharpness settingNumberSharp Reference GET Sharp or ?SHARP This retrieves the sharpnessSignalstatus Current image signal input status is returned asSignal statusID GSIGNALSTATUS=Signal statusIDTemp NumberTo 127.9 C GTEMP=5,37.1,63.0,38.9,29.7,32.4Setting None Reference TmplGTMPL=5,71.0,90.0,57.0,44.0,53.0 Tracking adjustment value is set to TRACK=Adjustment valueNumberTrack GTRACK=21Setting This sets the vertical keystone to VKSReference This retrieves the vertical keystone Adjust Setting This sets the screen color correction to NormalScreen color correction parametersID Reference This retrieves the screen color correctionSetting values for R/G/B adjustment valueNumber are -20 to Setting This sets R to 10, G to 11, and B toThis retrieves the RGB adjustment values WbrgbZcontdrv Zoom lens continuous control parameterIDThis stops the zooming This zooms to the wide-angle endZstepdrv Zoom lens step control parameterIDZSTEPDRV=Zoom lens step control parameterID Error List BadsequenceSystem Unknown Error Processing StartYES Other Appendix 1. Reset Items Normal LampOFF PMM

Related manuals

Manual 2 pages 51.19 Kb

WUX10 specifications

The Canon WUX10 is a highly regarded projector that stands out in the realm of professional display technology. Renowned for its exceptional image quality and advanced features, it is an ideal choice for corporate environments, educational institutions, and event venues.

One of the most notable characteristics of the WUX10 is its WUXGA resolution (1920 x 1200 pixels), which supports 16:10 aspect ratios. This high definition capability ensures that media presentations are sharp, detailed, and vibrant, crucial for capturing the audience's attention and conveying information effectively. The projector utilizes Canon's proprietary AISYS technology, which enhances both brightness and contrast levels, allowing for dynamic visuals even in well-lit rooms.

With a brightness rating of up to 10,000 lumens, the WUX10 delivers clear projections even on large screens or in expansive spaces. This high lumen output is complemented by a contrast ratio of 2000:1, which means deeper blacks and more vivid colors, thereby enriching the viewing experience. The projector's ability to render images accurately makes it suitable for various applications, from corporate presentations to cinema-like experiences.

The Canon WUX10 also supports multiple connectivity options, including HDMI, VGA, and USB ports, as well as wireless capabilities, ensuring compatibility with an array of devices such as laptops, tablets, and smartphones. This versatility allows users to seamlessly stream content without the hassle of tangled cables.

In terms of maintenance and usability, the projector features a long lamp life of approximately 3,000 hours in normal mode and extended to 5,000 hours in eco mode. This longevity reduces the need for frequent replacements and minimizes downtime. Furthermore, a filter-free design simplifies cleaning and upkeep, making the WUX10 a practical solution for users.

With its compact and lightweight design, the Canon WUX10 is easy to transport and install, making it a favorite among professionals who require mobility without compromising on performance. This projector not only meets the demands of high-quality projection but also embodies Canon's commitment to innovation and user-friendliness.

In summary, the Canon WUX10 stands out for its impressive resolution, high brightness, robust connectivity options, and user-centric design. It is a solid investment for anyone looking to elevate their visual presentations.