Canon WUX10 manual Error Processing, Start

Page 87

Projector WUX10 MarkII User Commands

8. Error Processing

START

Error judgment

Processing user command?

YES

 

Invalid (undefined)

YES

command?

 

Invalid command format?

YES

 

Command executable while

YES

 

power mode is OFF?

 

Power mode is "OFF"?

Command executable withYES PMM?

Power mode is "PMM"？

YES

YES

"BAD_SEQUENCE"

"INVALID_COMMAND"

"INVALID_FORMAT"

"NOT_POWER_SUPPLIED"

"NOT_POWER_SUPPLIED"

Switching power modes?

YES

"BUSY (POWER)"

Invalid parameter type?

YES

 

Undefined parameter ID?

YES

 

Incorrect parameter

YES

number?

 

Focus lens driving?

YES

 

Zoom lens driving?

YES

 

User image registration in

YES

progress?

 

"INVALID_PARAMETER"

"BUSY (FOCUS)"

"BUSY (ZOOM)"

"BUSY (LOGO_CAPTURE)"

Image mode switching in

YES

progress?

 

"BUSY (IMAGE)"

Signal setting (detection) in

YES

progress?

 

"BUSY (NOW_SETTING)"

Internal processing in

YES

progress?

 

"BUSY"

Revision History / Date

Changes

Revised by

Approved by

- 83 -

Page 86 Page 88
Image 87
Page 86 Page 88
Contents Projector WUX10 MarkII User Commands Revision History Table of Contents Error List Error Processing Other Appendix 1. Reset Items Same as or OverviewProjector can be controlled via serial or LAN connection Communication SpecificationsCommunication System Serial Request transmissions sent from PC to the projector Example Delimiters Delimiters for commands sent from PCERR response An error message is output ExampleCharacter string Or more Ascii characters 20h to 7Fh Or more Ascii characters 20h to 7FhTransmission sent Communication FlowAutopc Command SystemPower Auto SET Autosetexe Aspect Input Auto PC Autopc Command List PMM This includes the command function, conditions, and notes Details of CommandThis indicates the command format This describes the command responseFor details on other responses, refer to the Error List 6AXADJControl R hue is set to -8, and the color saturation is set to Setting6AXR-Y IOK is returned if the parameter was set properlyDo not combine Auto focusing is executed during auto setup executionAscombo Auto set combination parameterID CombineAspect Setting This sets the screen size to Wide ASPECT=169GASPECT=TRUE Autopc iOK AutopcAutosetexe Auto focusing is executedAvol SettingThis sets the volume to This retrieves the volumeReference BlankBlank parameterID Blank is set to onBlack screen Screen when Blank setting parameterIDSet to Black screen when screen is Blank BlankcolorReference This retrieves the brightness Setting values for Brightness settingNumber are -20 toSetting This sets the brightness to BRIThis mutes the Beep sound Beep sound settingNumber Beep sound mute Beep sound outputBVOL=Beep sound settingNumber BvolReturns the user command version as GCOMVER=User command versionCharacter stringComver Reference This retrieves the contrast Setting values for Contrast settingNumber are -20 toSetting This sets the contrast to +3 ContThis sets the dynamic gamma function to Weak DgammaGDOTS=1200 DotsDOTS=Number of dotsNumber DOTS=1650This sets direct power-on to OFF Direct power-on is set to onDpon ERR Fcontdrv Freezes image FreezeFreeze parameterID Image now frozen Image now not frozenFstepdrv Focus lens step control parameterIDFSTEPDRV=Focus lens step control parameterID Ftoneadj This sets the gamma correction to Setting values for Gamma adjustment Number are -10 toGAMMA=Gamma adjustmentNumber GammaGuide display is set to on Guide setting parameter ID Guide display onGuide Guide display OFFHPIX/VPIX HPIX=1024GVPIX= Reference This acquires the vertical position HPOS/VPOSReference This retrieves the hue Setting values for Hue setting valueNumber are -20 toSetting This sets the hue to +8 HUEImage GIMAGE=CINEMA Imageflip Video InputInput selection parametersID ComponentSetting This locks the remote control keys KeylockReference This retrieves the key lock state Silent cooling Lamp output setting parametersIDLamp NormalGLAMPCOUNTER=Lamp on timeCharacter string For all other responses, refer to Error ListLampcounter Returns current lamp on time asLang Setting LED display is set to on LedilluminateThis sets the LED display to OFF Lmpt None Reference This retrieves the lamp timeHours 34 minutes Main GMODE=REMOTE GMODE=LOCAL Mode switchMode reference ModeMute This returns the audio/beep sound to its original settingThis mutes the volume Reference GET Mute or ?MUTE This retrieves the volume stateGNOSIG=BLUE Parameters for setting display screen in no-signal modeIDThis sets the Blue screen when no signals are input NosigNo display Parameters for setting display screen at startupIDPjon Canon logoPMM Power management setting parametersIDExit mode Reference This retrieves the power management modePOWERParameterID PowerParameterID Power on Power OFFProdcode Product name is returned asGPRODCODE=Product nameCharacter string Progressive conversion setting parametersID This sets the progressive conversion setting to OFFProg DOWN+REP, Button press start Remote control emulation button parametersIDPOWEROFF, Power button pressed twice UP+REP, Button press startRC Power iOK Remote control setting parametersID Remote control channel This sets the remote control channel to ch1Rcch Current image adjustment reset ResetReset parametersID Lamp on time resetReset Lamptime Control This resets the lamp on timeRGB gain values are obtained Setting values for R/G/B gain settingNumber are -60 toSetting R gain is set to 10, G gain to 11 and B gain to RgbgainOr ?RGBOFFSET Setting values for R/G/B offset settingNumber are -60 toRgboffset RGB offset values are obtainedRomver ROM version of the firmware is returned asGROMVER=ROM versionCharacter string GET SAT or ?SAT SATReference This retrieves the color saturation SAT=-10Reference This retrieves the screen aspect Setting This sets the screen aspect toScrnaspect 1610 DisplaySEL Input signal selection parameterID AUTOAutoSEL=Input signal selection parameterID GSEL=Detected input signalIDGSEL=575p Setting This sets the input signal selection to AutoReference This retrieves the input signal GET SEL or ?SELReference GET Sharp or ?SHARP This retrieves the sharpness Setting values for Sharpness settingNumber are -10 toSHARP=Sharpness settingNumber SharpGSIGNALSTATUS=Signal statusID SignalstatusCurrent image signal input status is returned as Signal statusIDGTEMP=5,37.1,63.0,38.9,29.7,32.4 TempNumber To 127.9 CSetting None Reference TmplGTMPL=5,71.0,90.0,57.0,44.0,53.0 GTRACK=21 Tracking adjustment value is set toTRACK=Adjustment valueNumber TrackSetting This sets the vertical keystone to VKSReference This retrieves the vertical keystone Reference This retrieves the screen color correction AdjustSetting This sets the screen color correction to Normal Screen color correction parametersIDWbrgb Setting values for R/G/B adjustment valueNumber are -20 toSetting This sets R to 10, G to 11, and B to This retrieves the RGB adjustment valuesThis zooms to the wide-angle end ZcontdrvZoom lens continuous control parameterID This stops the zoomingZstepdrv Zoom lens step control parameterIDZSTEPDRV=Zoom lens step control parameterID Badsequence Error ListSystem Unknown Start Error ProcessingYES Other Normal Lamp Appendix 1. Reset ItemsOFF PMM
Related manuals
Manual 2 pages 51.19 Kb

WUX10 specifications

The Canon WUX10 is a highly regarded projector that stands out in the realm of professional display technology. Renowned for its exceptional image quality and advanced features, it is an ideal choice for corporate environments, educational institutions, and event venues.

One of the most notable characteristics of the WUX10 is its WUXGA resolution (1920 x 1200 pixels), which supports 16:10 aspect ratios. This high definition capability ensures that media presentations are sharp, detailed, and vibrant, crucial for capturing the audience's attention and conveying information effectively. The projector utilizes Canon's proprietary AISYS technology, which enhances both brightness and contrast levels, allowing for dynamic visuals even in well-lit rooms.

With a brightness rating of up to 10,000 lumens, the WUX10 delivers clear projections even on large screens or in expansive spaces. This high lumen output is complemented by a contrast ratio of 2000:1, which means deeper blacks and more vivid colors, thereby enriching the viewing experience. The projector's ability to render images accurately makes it suitable for various applications, from corporate presentations to cinema-like experiences.

The Canon WUX10 also supports multiple connectivity options, including HDMI, VGA, and USB ports, as well as wireless capabilities, ensuring compatibility with an array of devices such as laptops, tablets, and smartphones. This versatility allows users to seamlessly stream content without the hassle of tangled cables.

In terms of maintenance and usability, the projector features a long lamp life of approximately 3,000 hours in normal mode and extended to 5,000 hours in eco mode. This longevity reduces the need for frequent replacements and minimizes downtime. Furthermore, a filter-free design simplifies cleaning and upkeep, making the WUX10 a practical solution for users.

With its compact and lightweight design, the Canon WUX10 is easy to transport and install, making it a favorite among professionals who require mobility without compromising on performance. This projector not only meets the demands of high-quality projection but also embodies Canon's commitment to innovation and user-friendliness.

In summary, the Canon WUX10 stands out for its impressive resolution, high brightness, robust connectivity options, and user-centric design. It is a solid investment for anyone looking to elevate their visual presentations.
Top Page Image Contents